KHWV01RSS0 KitchenAid Washer - Instructions

Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.

door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench

To verify it was the motor making the noise not the drum bearing I removed the belt and rotated both by hand to see which one made naoise - then I ordered the motor.
To install the motor remove rear panel, slip belt off, remove 1 bolt holding motor in, carefully slide motor towards you until pivits disengage. Wires are ling enough to set motor on bottom of washer and rotate for easier access to connector. Install motor in reverse sequence.

twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though

1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

I followed the repair blog by the poster most liked...

It took a few minutes to realize that the part slide into place instead of snapping in. In order to get the part to slide into place i put my head in the washer to hold the drum in place then with both hands slide the part into place.

remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

I read the instructions once and then started. It was easy but did take an hour to do the entire job.

After removing the Top Cover and back cover by removing the 3 screws for the top and 10 screws on the back cover to expose the interior of the machine. Remove the rubber hose that was attached to the bottom of pressure switch. Pushed gently upward on the pressure switch until it popped out. Gently press down on the 2 small tabs on the plug and then gently pull the plug out. Placed new pressure switch in place, plugged the connector back into the switch. Also doubled checked the hose to ensure that the tubing has not rubbed a hole it from rubbing on the concrete counter balance. If yes then remove the tube from the bottom of the washer and replace with approximately 2 feet of 3/16 inner diameter/1/4 outer diameter tubing. Attach the new tubing to the bottom of the washer port and the pressure switch. Attach the new tub to the water discharge hose using tie wraps or electrical tape to ensure not to occur again.

Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.

Unplug power and turn off water. Top of machine comes off by removing three screws at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.

Great move, easy, and saved myself the thick end of $200.

I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps