11027086600 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bonnie from Baytown, TX
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brett from seymour, IN
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tntsplace.com from MCALLEN, TX
- Parts Used:
- WP8563964
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old hinge broke, door did not open and close right.
I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Carrollton, TX
- Parts Used:
- WPW10119828, WP8563964
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hinge pins were sheared off
I removed the screws holding the broken hinges and put the new hinges on. It only took a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Glennville, GA
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
washer would not drain water
need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from asheville, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from germantown, TN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer wouldn't go in the spin cycle-
Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harley from Flower Mound, TX
- Parts Used:
- W10435302
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Bearings noisey
Followed instruction sheet. Removd tub assembly, Laid, washer on side, removed motor and necessary wiring, removed drive shaft, bearings and seal assembly, cleaned all areas, installed new parts. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Ormand Beach, FL
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from linthicum, MD
- Parts Used:
- WPW10419333, W10183157
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer not rotating F 51 Code RPS Failure exhibited
1. Removed tub to ensure nothing caught to stop rotating. 2. Removed rotor and noted stator had fracture across center from coil to coil. 3. Changed stator, RPS and harness. 4. tested and received F 50 code (no rotation sensed by RPS.5. Changed RPS control board-washer works fine. Hope this repair acts as having a new washer again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Hedgesville, WV
- Parts Used:
- W10435302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Bearing's were shot and seal leaked water every where.
Replaced bearings, seal and new shaft. Washer never sounded this good, well I can't even tell it's running now. Very quiet. Just watch all the you tube vids on replacing seal and bearings and you shouldn't have any problems !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from League City, TX
- Parts Used:
- W10435302
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Top bearing frozen and had to be cut out
Using instructions that came with parts and google and utube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Valparaiso, IN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Code F51 Washer would not spin.
I disassembled the top half of the machine removed the drum and found a bad bearing. The code F51 said i had a bad motor control board. I had a frozen bearing on the main shaft. Freed up bearing, machine now runs but I need to replace the bearing,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from King George, VA
- Parts Used:
- W10536347
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Drain Pump Leaks
Disconnect power and water. Remove the back panel of the washer. The drain pump is on the lower left corner (looking at the washer from the back). Access the electrical connection to the pump motor by lifting the lid where the wire enters the motor. You should be able to do this with your fingers and moderate pressure. Disconnect the electrical plug from the pump motor. Use pliers to remove the two hose clamps, one on the inlet and one on the outlet. Water may leak at this point so have some towels ready. Using a 5/16 wrench/nut driver, remove three hex head self threading bolds that connect the pump and motor to the underside of the tub. The replacement pump and motor go in in reverse order. Note that the replacement pump comes with a moisture shield. The shield installs on top of the new pump between the tub and the pump. It is difficult to see how the shield fits in place when fitting it to the replacement pump. The best way to see how the shield fits in place is to align it on the tub where the defective part was removed. Before testing the repaired washer, consider removing the inner tub and drain compartment cover (located at the bottom back of the inside of the washer). This takes some effort; however, it will save you from repeating this repair. Look for coins or other debris under the inner tub. For instructions on removing the inner tub and drain cover, go to youtube to watch or search for the model number and tub removal on your favorite search engine or youtube. Finally, use the spin and rinse cycle to test the repair. Look to see the pump drains the washer and ensure there are no leaks around any of the hose clamps. Good luck with your do it yourself home repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Gore, OK
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
washer kept going out of balance
Removed cover and removed rods,replacing them one at a time.
Was this instruction helpful to you?
Thank you for voting!