Models > 11027086600 > Instructions

11027086600 Kenmore Washer - Instructions

Jump to:

All Instructions for the 11027086600

Customer:: Joaquin from Santa Clarita, CA
Parts Used:: W10820048
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers

Washing machine was rocking a lot, and stoping too much.

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

Was this instruction helpful to you?

Customer:: Charles from Houston, TX
Parts Used:: WPW10419333
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Socket set

machine gives uneven load alarm and f51 error code

Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.

Was this instruction helpful to you?

Customer:: Neil from Onalaska, WI
Parts Used:: W10536347
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers, Wrench set

Water would not drain

I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.

Was this instruction helpful to you?

Customer:: JESUS from PORT ARTHUR, TX
Parts Used:: WPW10619844
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

did not work

reemplace the lid lock assembly

Was this instruction helpful to you?

Customer:: Jose from Verobeach, FL
Parts Used:: W10536347
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Socket set, Wrench set

Won't drain the water

It was not easy but I dit my sell

Was this instruction helpful to you?

Customer:: James from Alvin, TX
Parts Used:: W10820048
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The washer was trying to walk off during the spin cycle.

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

Was this instruction helpful to you?

Customer:: Shawn from Indio, CA
Parts Used:: W10820048
Difficulty Level:: Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers, Socket set

Washer was noisy and had a lot of movement

The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.

Was this instruction helpful to you?

Customer:: Janelle from Gray, ME
Parts Used:: W10536347
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

water leak at pump, crack in pump housing

First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump

Was this instruction helpful to you?

Customer:: Josh from Lodi, CA
Parts Used:: W10820048
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins

vigoirously shaking causung UL code

Replaced rods with new set of 4

Was this instruction helpful to you?

Customer:: Jacob from Glennville, GA
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

washer would not drain water

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Was this instruction helpful to you?

Customer:: richard from asheville, NC
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

replaced leaking pump

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

Was this instruction helpful to you?

Customer:: william from germantown, TN
Parts Used:: WPW10189966
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

washer wouldn't go in the spin cycle-

Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.

Was this instruction helpful to you?

Customer:: tntsplace.com from MCALLEN, TX
Parts Used:: WP8563964
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Old hinge broke, door did not open and close right.

I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.

Was this instruction helpful to you?

Customer:: James from Carrollton, TX
Parts Used:: WPW10119828, WP8563964
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Hinge pins were sheared off

I removed the screws holding the broken hinges and put the new hinges on. It only took a few minutes.

Was this instruction helpful to you?

Customer:: axel from lighthouse point, FL
Parts Used:: W10820048
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

drum made loud noise

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Was this instruction helpful to you?

All Instructions for the 11027086600