Models
>
79641379211
79641379211 Kenmore Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 79641379211
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$26.80
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
$72.90
If your washing machine is leaking, slow to fill, will not stop filling with water, or is not filling at all, the cold-water inlet valve may be defective. The purpose of the valve is to open to allow ...
In Stock
$63.71
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
In Stock
In Stock
$41.72
This hose has bellows to allow for flexibility during the wash and spin cycles.
In Stock
$85.65
The door lock assembly is a genuine OEM part for your washing machine. This part informs the washer that the door is closed and locked in place, which allows the machine to start its cycle. If you are...
In Stock
$41.72
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
In Stock
$27.79
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
In Stock
$31.32
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
In Stock
$214.57
This part is the replacement spider, or washer spinner support, for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub or basket whi...
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 79641379211
Viewing 13 of 13Leaking
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Harrisburg, PA
- Parts Used:
- 6501KW2002B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more
motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from STOWE, VT
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northport, NY
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
Was this instruction helpful to you?
Thank you for voting!