11021102013 Kenmore Washer - Instructions

I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose

Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.

online videos were great. called to order and lady was very helpful. washer is now operating normal

1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

Took the Cover off and installed belt.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!

followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.

Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem

Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.