11021182013 Kenmore Washer - Instructions

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

Removed the fabric softner despenser on to of agitator.
Removed the filter inside the agitator, pull straight up
Removed the bolt in the center of the agitator using a an extension on a 5/!6 socket.
Pulled the agitator out of washer removed inner works by hand. There are 4 fiberglass parts with teeth on them, I removed these 4 units and replaced them with new ones and it them put agitator back together in the reverse order. Works great.

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

1St I took the top cap from the agitator, I then removed the middle cap. I then removed the 7/16th bolt from the middle of the agitator and removed the agitator. I took the old broken parts out and replaced them with the new parts. I then put everything back together in the reverse order tried the washing out and it works great. Actually I just followed the instructions, which took 20 minutes, and everything was kopacetic.

It was really easy. I popped off the agitation cone cover, used a socket set to remove the bolt which holds it all together. I removed the broken part, assembled the new one, using the old one as a example. I installed the new one. . . And I have clean clothes again. So much better to fix the old machine then buy a new one. . .

Removed top of agitator, then removed the nut holding the agitator in place, pulled up the second piece of the agitator, replaced dogs and put the agitator back together

first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.

Removed top agitator cover. Removed bolt and pulled out the cam holding the dogs. Assembled new cam w/dogs put in place and installed bolt plus agitator cap and was ready to wash.. Very Simple

1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!

I pulled the top off ( the fabric softner dispenser) unscrewed the nut pulled up on the agitator replaced the ears put it back together. . It works just as good as a $75.00 an hour repairman could have done. And the wife wanted a new washer? Ha

I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.

took the cover off the top of agitator, removed 3/8" bolt that went through cam and secured agitator. removed agitator and replaced the 4 agitator dogs and cam.
replaced agitator, tightened bolt, replaced cover. the washer works like new again? thankyou for your help and the correct parts.

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!