11021292013 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ramona from MESA, AZ
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Water drained but would not spin.
Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Kernersville, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Top half of agitator would not agitate.
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.
PS Received parts in 72 hours. $10.00 bucks and never left the house.
PS Received parts in 72 hours. $10.00 bucks and never left the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Cleveland, OH
- Parts Used:
- WPW10074580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Found seal had split on agitator cap
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.
Thanks for making finding part so easy . . . .
Thanks for making finding part so easy . . . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Milwaukee, WI
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Replaced the dog ears.
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VACAVILLE, CA
- Parts Used:
- W10440729
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Spin cycle was way out of wack, like it was over loaded to 1 side
1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Saint Cloud, FL
- Parts Used:
- WPW10276397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Remove and replace drain pump
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INDIANAPOLIS, IN
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
would not spin
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LONG BEACH, NY
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud banging during spinning
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEXAS CITY, TX
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
machine wobbled violently
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Mount Vernon, WA
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Timing tabs securing the agitator center
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WHITEWATER, CA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Not really a problem but the hardest part was moving the washer to lay on its back.
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard E from BURKE, VA
- Parts Used:
- WPW10683603
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water leak into washer drum
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this instruction helpful to you?
Thank you for voting!