11022102312 Kenmore Washer - Instructions

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.

I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.

remove top of adigator and remove bolt. remove plastic clip and cogs.replace in reverse order.

Part ordered was incorrect even though your website said that it was correct when I ordered it. Part sent back. Have since bought a new washer. Your contact person to return part was very helpful.

Unscrewed the back plate,, unscrewed the top section from the back ,tipped the machine back after unlocking the front two suspension rods, put the new ones in with the new locks , tipped the machine forward, took the two back, suspension rods out, put them back in with a new locks put everything back together made sure all the legs were level and recalibrated the machine, which is take dial turn counterclockwise a turn stop on this machine at the regular pointer. Go back one go forward three back one you’ll see all the lights blinking turn to the light that has rinse and hit the start button. It will recalibrate and everything is working fine thank you all they were better rods than what I had ordered. One time before online. These appeared to be the original ones. Which are made better so make sure you use them. Thanks you saved me 600 bucks.!

open lid pop cap off top of agitator remove sealing cap unscrew bolt pull off top of agitator may need to work it back and forth reach in pull out dogs holder replace and grease then reasimble

Pop the agitator cover off with a screwdriver, remove the agitator retaining bolt, pull off agitator,seperate, install cogs and reasemble.

I followed the diagram and instructions included in the kit. I removed the plastic cover on the agitator, then another plastic cap inside the agitator. loosened a 7/16 bolt-removed agitator from washer. After removing agitator, Directional cogs and gear assembly inside agitator removes easily-pull out or turn upside down. Re-assembly was easy-almost fool proof . Using the instructions and diagram included with Directional cog package made it a snap.

Took off top cap of agitator then removed cover that is over the bolt that holds the agitator to the shaft.
With a rachet and extension & 7/16 socket and holding bottom of agitator still so the bolt could be broken loose then holding only the top of agitator to
loosen the bolt the rest of the way. It had been in for
so long the bottom of the agitator had to be broken loose and then the top of the agitator came off like it
was suppose to. Then I took out the gear that has the Agitator Directional Cogs attached to it and took
out the old COGS and replace them with new COGS. Held the top of the agitator upside and put
the gear with the new COGS. So the cogs wouldn't fall out and slide the gear into place and then turned the agitator right side up & put it back on the
washer Machine. Had to use pliers to hold the bolt
straight to line it up and put the bolt in place then
tighten bolt job is complete.

The retainer was broken and likely because the washer was worn down and allowed the whole thing to move more and more over time. Got the exact parts I needed and the repair could not have been easier.

popped out the top (softener cup) opened the nut with a 7/16 wrench with an extension. The agitator assembly popped out then the plastic clip was removed upside down because there you get to replace the Cogs.

No problem