11081375340 Kenmore Washer - Instructions

Removed backing and hoses and replaced the water inlet valve.

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

removed top panel and back panel
and then disconect the two wire fromm water inlet
fallow by removing screws.disconect water hose
then put back new part make sure i have all same conected as original put back panel top and back
conected hose for water back and electric .
then i turned 0n cold water perfect work hot water perfect warm perfect. problem fixed.
thanks. pedro

First - I saw the picture of the part on your site. It made all the difference.
Then, I turned off the water supply, unplugged the washer, removed the screws holding the backing plate on the washing machine to expose the valve.
After that, it was as easy as removing two mounting screws, disconnecting the solenoids (just two connections), pulling out the old valve and replacing it with the new.
Pretty simple and a lot less pricey when you can wait a few days for a part to come in the mail.

I just followed the instructions from a previous customer. Worked perfectly.

I watched the video on changing the valve. Then ordered the part. The video showed exactly how to do the repair and it was so easy.

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

I followed the instructional video that referenced the water inlet valve. The steps I followed were identical to the video I watched. That was extremely helpful. The hardest part was removing the terminal wires that connected to the inlet valve, the rest was very easy. With the new valve installed the washer works exactly as it did before. This site is very helpful, thank you!

Followed the instructions on the Part Select video which were very clear. I removed control module from top of washer, pulled the washing machine outer housing forward slightly and disengaged the rear closure panel slightly. I disconnected the electrical harness and then I was then able to remove the existing inlet valve. The new valve was then installed and the precess reversed to complete the installation.

Piece of cake!! (The water comes pouring into the machine now)

I'm a 61 year old single woman, rather handy around the house. I followed the video which was very helpful and everything went together fine until it came to putting the body of the machine back on. I did the repairs all myself which took about an hour but when it came to the machine body I couldn't get it back on there after numerous tries. I had to call my brother and it took him just one try but then he is 6'2" and could look down the little hole to see where the tab was to put it on and hold the body at the same time. BTW - he did inspect my work before finishing the job and said I "did good!" Thanks for the video but could have used some hints as to how to put the body on with some close ups as to what he was doing with his hands when he did it.

Our washer's cold water flow became very slow. We were living with just hot water washing for about a month. I had used PartSelect in past and have always been very satisfied with the outcome. So, I went on the site and within a couple of minutes of navigating, had the part (water inlet valve with mounting plate) on order.

I watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).

I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.

With the help of reading about other individuals and their problem, I was able to replace the water inlet valve in less than 30 minutes. Unscrewed two screws on top to reveal the flat springs. Popped the springs and released the back of the washer. Removed the old part and replaced with new. A lot easier than I thought.

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

I diagnosed by reversing the plugs on the hot/cold valves. I then removed the valve , cleaned it up and sprayed the electrical contacts with (Corrosion Block) and re-assembled. It still only had hot water. Ordered part, received part next day. When I went to install it I discovered that the (Corrosion Block) had penatrated and all was working! So now I have a spare valve.

Opened back panel and replaced valve - very easy