11045976403 Kenmore Washer - Instructions

I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.

Go to u tube video gives instructions. Very easy to replace

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

It was fast and pretty easy to do.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.