41744052500 Kenmore Washer - Instructions

Removed broken Vane and reinstalled replacemnet real time repair 2 minutes. It took longer to open box than to fix.

Took the old one off and snapped in the new one.

Unscrewed the old striker and screwed in the new one.

Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

There were only two screws that held the door strike/catch in place. I had to fish out the broken plastic piece with a pair of hemostats. The only difficult part about changing the new piece was that I had to find someone with the correct screwdriver to use since it was not a standara screwdriver. Luckily I live next door to a mechanic and borrowed his. The two screws came off easilty and I was able to replace it in 2 minutes. I was thrilled that the part that I ordered arrived the next day.

It was very easy. I simply unscrewed the 2 screws set the new latch into place and replaced the screws.

With the help of PartSelect's diagnosting tool it was easy to find the right part. The part arrived very fast and the installation was "child's play" by following PartSelect's video. I must have saved > $100. Thank You very much. -Anna-

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.

I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.

Watched the video on website and followed what they said. Worked great.

The part ordering and arrival was very easy and fast. Problem with the directions on removing the damaged drum vane. They were not clear directions. Once I figured out what needed to be done it went easy

This repair was pretty simple. Unplug washer from electrical outlet and remove hoses. This is a good time to replace the hoses. Removed two screws at the back of the washer to remove the top of the washer. This exposed the faulty valve assembly. Disconnect the three connections. There are two screws holding this part in place. The top one is easy to remove, the bottom one is a little more difficult due to access. Remove plastic retainer plate on back of washer. Remove faulty valve assembly. There are two rubber grommets/gaskets that will need to be removed from the faulty part and installed on the new part. Slide new assembly into place. Secure with the two screws. Replace retainer plate. Reattach power connections. Reattach hoses and finally Reinstall top of washer. Total time was right around 30 minutes.

Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!

Removed and replaced two screws.