11026152500 Kenmore Washer - Instructions

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

First I removed the liquid fabric softener cover, then removed the seal with my fingers, then used a socket with an extension to remove the single bolt that holds the agitator to the spindle.

Next, I pulled up to remove the agitator and tipped it upside down to take out the centrifugal mechanism. Then, I simply replaced the old parts with the new ones, and put it back together, as it shows in the included diagram. It took about fifteen minutes.

I was glad to be able to go online, and quickly locate the exact parts our machine needed, at a reasonable price! Our machine now works like new again.

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.

Replaced motor starting capacitor. Noticed water leak at pump and replaced pump

First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.