11045091403 Kenmore Washer - Instructions

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

turned off water valves , disconnected and placed hoses into small bucket . removed top . I then removed screw off old valve , shimmied it out of the hole , removed hose with pliers , slipped off white set of plugs and then black set .. Then I put hose on new valve , placed plugs ( black & white ones ) be sure to mark the correct side .. for me two white were on the right side of valve and black on left side .. placed valve back into its respective spot . attached the screw .. note I sled mine to the right just a bit and all lined up perfectly . Attached hoses , ran test cycle on warm , cold , hot .. All hoses were hooked up correctly and leak free . put lid back on and perfect .. The hardest part , was moving the shelves above my washer , really was super simple . Watch the video twice. You will be able to do it in no time. Saved me 245$ . From my appliance shop the part 150.$ 100 service call and the install fee $ since the install was so easy couldn't be much but .. Its a guesstimate ..You can do it !

My hubby and I replaced the part in about 20 minutes, including moving the washing machine. We love doing household projects like this. We're a great team and putting in this part showed how good we work together. Thanks for the quick response too!

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

It was fast and pretty easy to do.

Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the inside. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

so easy!!three screws to take top off,one screw held valve in take hose off then install new part and reverse take apart order and done!!!Would have been sick if had to pay service call for such a easy fix!! Mike

REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.

Shut water off to washer, unhook hoses, removed back panel of washer, removed screw that holds the valve in place then unhooked the water line that connects to the washer and removed part. Place new inlet valve in position and hooked hoses and mounted it in place, put back panel back on and hooked hoses up and turned water on. Did a test wash and it worked

Need to elongate the hole in the frame to allow the screw that holds the valve in place to be inserted. You could not even start it as is. Also it put pressure on the valve so it would not seat properly. Need to include in the instructions you may need to elongate this opening in order to complete this repair. Other than that is was extremely easy. Parts fit well. Video instructions were great. Other than not knowing about the valve screw placement changing both pieces were extremely easy. Washing machine was repaired within minutes and is functioning properly again. Even the diagnosis tool was excellent as I have no experience with repairing washing machines but your site helped me trouble shoot the issue, order the parts (and receive in a couple of days) and replace the defective pieces in minutes. Changing these 2 items got me up and running an days and cost significantly less than what a repairmen would have charged just to show up at the door. Appreciate all your help!