Models > 11027032601 > Instructions

11027032601 Kenmore Washer - Instructions

Jump to:

All Instructions for the 11027032601

Customer:: James from Alvin, TX
Parts Used:: W10820048
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The washer was trying to walk off during the spin cycle.

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

Was this instruction helpful to you?

Customer:: Shawn from Indio, CA
Parts Used:: W10820048
Difficulty Level:: Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers, Socket set

Washer was noisy and had a lot of movement

The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.

Was this instruction helpful to you?

Customer:: david from knoxville, TN
Parts Used:: W10183157
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Socket set

washing machine showed F50 code

I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over

Was this instruction helpful to you?

Customer:: CARROLL from HENDERSONVILLE, NC
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers, Screw drivers

Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump

Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

Was this instruction helpful to you?

Customer:: Elijah from Point Hope, AK
Parts Used:: W10193886
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Socket set, Wrench (Adjustable)

UL flashes, will not spin, really loud,& black spots under washer

We ordered the outer tub & bearing and now the washer works like it was brand new.

Was this instruction helpful to you?

Customer:: Delinda M from Chicago, IL
Parts Used:: WPW10189966
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

f1, code on the face plate of the washer,we kept on resetting it

we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

Was this instruction helpful to you?

Customer:: Ronald from Demopolis, AL
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers

Washer making noise down close to bottom of machine.

First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.

Was this instruction helpful to you?

Customer:: Janet from Colfax, WI
Parts Used:: WPW10072840
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replace a seal

Just had to remove cap on agitator and replace new rubber seal.

Was this instruction helpful to you?

Customer:: william from germantown, TN
Parts Used:: WPW10189966
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

washer wouldn't go in the spin cycle-

Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.

Was this instruction helpful to you?

Customer:: Lorraine from Millsboro, DE
Parts Used:: WPW10072840
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

broken seal

went well but alas the problem still exists.

Was this instruction helpful to you?

Customer:: Ralph from New Milford, NJ
Parts Used:: WPW10074580
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

The seal was broken on the agitator cap barrier

Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.

Was this instruction helpful to you?

Customer:: Jacob from Glennville, GA
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

washer would not drain water

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Was this instruction helpful to you?

Customer:: richard from asheville, NC
Parts Used:: W10536347
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

replaced leaking pump

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

Was this instruction helpful to you?

Customer:: Gregory from Sandy Springs, GA
Parts Used:: WPW10072840
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Lots of gunk between fabric softener dispenser and where it attaches to the agitator

Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!

Was this instruction helpful to you?

Customer:: axel from lighthouse point, FL
Parts Used:: W10820048
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

drum made loud noise

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Was this instruction helpful to you?

All Instructions for the 11027032601