11047567701 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Tower Hill, IL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
replace drain pump
The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from elizabethton, TN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer washed cloths then would not rinse
Just went by instructions provided by parts web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from HARRAH, OK
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
would not drain or spin
Replace water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from Austin, TX
- Parts Used:
- WP8540221
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door strike broke
other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- amber from rochester, WA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the pump went out on the washer
took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from Havre, MT
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
F 21 error
We purchased a new pump and installed it very easily. My washer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Charleston, MS
- Parts Used:
- WP8540751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water in tub when not in use.
Received water valve in three days, remove top on washer, removed old part and replaced valve with new one, real easy fix, any one could do this. PartSelect confirmed this was the problem and part I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith M from Apple Valley, CA
- Parts Used:
- WPW10111435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The bottom conter balance broke in half.
Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Federal Way, WA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
machine flashed code for water not draining fast enough
I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Cherry Valley, IL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No drain fault code F-21
Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from New Richland, MN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
It was making lots of noise. Halfway through the cycle it would not pump all the water out
First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Waco, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn' drain f21 then after I drained it it gave f33
Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Denver, PA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
needed to replace water pump
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from La Puente, CA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
My washer would not drain, weird noises, etc.
This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.
Was this instruction helpful to you?
Thank you for voting!