11047567701 Kenmore Washer - Instructions

I purchased the downloadable Maytag Maintenance Manual (PDF format) and followed some of the directions and pointers from this web site. All in all, it was a pretty simple process. 1) Take the top off - 3 metal screws, 2) take the control console and detergent dispenser out - 1 T-20 Torx screw and multiple plastic clips and 1 wire connector, 3) take the lower panel off - 3 metal screws, 4)take bellows retaining ring off -- spring retainer used a needle nose pliers, 4) take off door latching mechanism - 2 T-20 Torx screws and multiple clips + 3 wire connectors, 5) take front panel and door off - 4 metal screws, 6) remove bellows retaining clamp with phillips screw driver, 7) remove old bellows. Reverse the process to install new bellows. On installation, make sure that bellows drain holes are at the bottom of the door. Also, hardest and most time consuming part was installation of the metal retaining ring (spring retainer) fought with it for about a half hour before I finally got it on. BTW all metal screws for my machine were 1/4" head the remainder were all Torx T-20. Good luck!

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp after it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

Took less than 5 minutes to replace, So Happy;-)

put in push down push back until they lock in

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!