11046757801 Kenmore Washer - Instructions

The new piece just took seconds to install. You had to set the piece slightly farther back then where it belongs, and with a slight downward pressure, just slide the part toward yourself until you hear it click into place. About 5 seconds and no tools required.

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

Did it myself, found the model # from your website, received the part, it slid right on,yay, no more tears in my sheets!

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

Very simple repair. Lined up the baffle tabs with the drum slots. Pushed the tabs into the slots, pulled the drum baffle towards the opening of the wahser until it seated. You will hear aclick.

Very simple repair had to remove door from Washer, loosen the seals so that I could remove the old hinge. Inserted new hinge place the door and hinge on brackets and tightened the screws. I was very pleased with the fast action in getting me my parts, less than 24 hours.Thank You.

Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

Remove top (held on with 3 screws on the back). Pressure switch is at the back right side. Remove rubber hose. Gently pry switch from side of machine. Remove electrical connection. Install electrical connection on new switch. Snap back into side of machine. Replace top. This was installed a couple of weeks ago and have not had either code since

Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Replaced water pump

Easy peezy!! Next day delivery, as promised for parts that could not be found anywhere else. I placed the baffles in the washer and clicked them in using both hands one by one. I'm petite and weigh about 110 lbs. The total installation time was less than 2 mins. I was given a $200 quote just for installation but, spent less than $100 and installed myself. Thank you!! I will not wait so long and shop around next time. I'm going straight to partsect.com to save time and money. Although I have to buy new clothes now since my washer put holes in all my clothes. But, the problem is finally solved and I am so grateful.