11046757801 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phyllis from Ridgefield, WA
- Parts Used:
- WP8183202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
screw arm that connects the two hinge parts broke after 15 years
Had difficulty getting the door off the washer because I didn't realize there were two hooks in addition to the two screws that held the door to the washer. I reviewed the repair video several times through out the repair. Probably unscrewed more than I needed. Got the new hinge installed on the door. The problem was I couldn't hold the door at the right angle to get the hooks inserted. The washer is near the wall so I couldn't open it all the way and bending over at an odd angle didn't help. At nearly 80 I don't have the strength I used to!! After trying and with the door falling on my arm I gave up and called a friend. We did have difficulty getting the hooks inserted correctly. I held the door and she got the hooks in. On the good side, the hinge part fit like it should!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from TULSA, OK
- Parts Used:
- WPW10352973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLYMOUTH, IN
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
WASHER WOULDNT DRAIN F21
REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Edgewater, NJ
- Parts Used:
- WPW10415587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Error Messages: "SUD" and "F35" Aborted Wash Cycles
Confirmed the issue was not a blocked trap at teh base of teh machine. Renoved the top of the machoine (Three 7mm hex-head sheet-metal screws). Removed the small hose (rubber tube) from the Water Level Pressure Switch. Confirmed the hose was not blocked or constricted. Removed the failed Water Level Pressure Switch by pinching the spring-retainer with needle-nose pliers. Mounted the replacement WLPS. Connected hose. Tested the machine. PartSelect online catalog and delivery service was painless, quick, correct, only a little over-priced and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Chester Springs, PA
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer baffle came off,plastic claps had broken
It took me a minute to put the baffle in place. The piece got here in one day. I would order again from here if I ever need any parts for any of my appliances. Thanks Anne B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Pigeon forge, TN
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken piece in tub of washer
This was so easy to swap the parts out. The plastic hooks that hold the pieces inside our washer had just worn out. We put our washer and dryer through LOTS of use and I am amazed it has hold on this long! The broken piece just popped out and the new piece just snapped right in. Thank you for your speedy shipping and the great price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Monett, MO
- Parts Used:
- WPW10415587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
5UD and F35 errors, would not run.
unscrew the top 3 screws that hold the top lid on. Locate the pressure switch on the back right side, near the top. Pop off the pin plug (wire pack)and pull off the black hose. Put the pin plug into the new switch then put the black hose on. I did notice that the new pressure switch was a little bigger than the old one. It did not want to pop into the retainer clip location so I just let it dangle. Its not a problem. Washer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rohn from Libertyville, IL
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Drain codes
After diagnosing codes noticed no drain replaced pump asm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from independence, MO
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not drain..."Suds"
I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Svitlana from Springfield, VA
- Parts Used:
- WPW10415587
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Machene performed no washing cycles. SUD and F35 errors on display.
Unplugged the machene. Removed the top cover (3 screws on back top). The pressure switch is back on the right wall. Turned it clockwise until its top almost pointed forward (at me) and it could be removed. Disconnected if from its wiring (pushed small tab down with my nail and pulled it out); and from the black tube (secured the tube with scotch tape, so that it wouldn't slip down inside the machene while I work). Unpacked the new switch, connected it to the wiring and to the tube, pushed it in place (square(ish) hole) until it clicked, put the top cover back in place (needs to be slid in front) and screwd three bolts holding it into their places.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Angola, IN
- Parts Used:
- WP8183196
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
F-70 heartbeat failure
The repair went very easy after locating the repair manual inside of the washer. The service manual gave all of the codes that the machine can give. Checked the F-70 code and it stated to unplug the motor control unit. Once that was unplugged the led lights came back on and it acted like it could run again. New unit put in in less than 15 minutes. I'd suggest to have it over nights because the unit I received through UPS was very badly damaged on the outside but plugged it in and it still worked. Two weeks running and a lot of laundry later; still going well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Granger, IN
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken part
The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bunnlevel, NC
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
would not drain
replaced drain pump.Saved 200$
Was this instruction helpful to you?
Thank you for voting!