11027272600 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Port Saint Lucie, FL
- Parts Used:
- WP3363394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Loud Screeching noise when draining water
On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Hillsboro, TX
- Parts Used:
- 3949247
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Tub would fill and then go through the wash cycle. When the rinse spin cycles came on nothing happened. Everything was dead.
Unplugged the AC cord and turned off the two water lines. Removed the control panel on top of the machine by removing four screws. Removed two clips that fastened the top of the machine to the rear panel. Tilted the cabinet forward a little bit and unplugged the switch. Removed the switch with the two philips screws and installed the new switch and plugged in the plug on the end of the wiring harness. Then reassembled everything. Cleaned the mess and plugged in the AC cord. turned the water on and everything worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Grand Haven, MI
- Parts Used:
- WPW10358149
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Cracked drain tube.
Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BREEDING, KY
- Parts Used:
- 3949247
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
lid switch failure
Pretty much like shown in the video tutorial however I didn't disconnect the water hoses. I unplugged the machine and pulled it forward 6 inches. Took it apart like in the video but because of space restrictions I took the cabinet into another room to replace the switch and then re-assembled. The hardest part was getting the cabinet to re-seat as before. It took several attempts but it's all done and the machine is working like a champ. I listed a magnet because I use them to keep the nuts and screws from getting lost
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MILWAUKEE, WI
- Parts Used:
- WPW10250667, WP63907, 8316845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water was leaking out to floor after each load
Replaced the springs after watching the video's from this site and problem has been solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from DAYTON, KY
- Parts Used:
- WP63907
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
drum SLAMMING into the back of the washer when sipnning
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from lindside, WV
- Parts Used:
- 285744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer shakes and was very noisey
researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryanne from BEND, OR
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Drain hose leaking
Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Coleen from Amenia, NY
- Parts Used:
- 3949247
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer washed , but wouldn't go into next cycle
unplugged washer. Remove 4 screws (Phillip's screwdriver) from back panel. Lift panel up. unplug switch remove ground wire (open end wrench) Remove ground screw. Removed switch wire from clips. Put in new switch & ground wire-less than 30 minutes.
Your service was excellent! Fast
Worse was moving the washer
Your service was excellent! Fast
Worse was moving the washer
Was this instruction helpful to you?
Thank you for voting!
Washer excessive vibration during rinse spin
Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.
Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from JAMESTOWN, PA
- Parts Used:
- 3360629
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
The washer would drain, but was screaming while doing nothing else.
The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.
I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.
The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.
I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.
The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Roca, NE
- Parts Used:
- WP8546127
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Retainer clip for the pump missing, caused pump to fail
Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from Houston, TX
- Parts Used:
- 285748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
I noticed that in the spin cycle the machine did not sound like it was suppose to. So I took the time and watched it go thru the steps and saw that it was not spinning.
Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando from Graham, NC
- Parts Used:
- WPW10358149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Drain hose
to change it was 1,2,3
thank you guys
thank you guys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eddie from lockesburg, AR
- Parts Used:
- 285871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
pipe had a hole
I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.
Was this instruction helpful to you?
Thank you for voting!