11020957991 Kenmore Washer - Instructions

slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

Watch the video

Looked at the repair instructions on your web site and it made the repairs simple and easy.

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

After moving washer and UN-Plugging electrical. 1. Remove the 2 screws that hold the Control Panel to the lower chassis. 2. Lift the Control Panel up and forward to expose the water level switch. 3. Remove the dial. 4. Remove the old switch, (a plastic tab locks it into the panel, try to release it(from the front) with a small screwdriver, (mine broke off, releasing the switch). 5. Remove the electrical connection by lifting the connection locking tab. 6. Remove the air tube. 7. BLOW into the air tube to ensure it is not blocked. 8 . Reconnect the air tube and electrical connection. 9. Carefully install the new switch into place, turning it to line up and lock the tab into the panel. 10. Re-install the dial and return the Control Panel screws into the lower chassis. NOTE: If the included air hose needs to be replaced, the time and difficulty needed to make repairs will increase.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next day shipping came the next day .
Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight.
Videos, parts diagrams and instruction are great, regular freight is not good

Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....

I had no idea what the problem was...other than the drum would not spin and it made a horrible noise...so I figured the motor was still good. I figured the repair man would charge me $200 and a new washer is $300...so what have I got to lose? First, I unplugged the unit. I started by removing the top control box by removing two screws in the back of it. Once off, there are two big clips which hold the body in place. That came off easy. I removed the back next and now had everything out in the open. I disconnected the exit greywater pump which was easy with two snaps. I tipped the unit on the side and removed the motor - also attached with two snap on clips. Between the motor and the gearbox there is a shock absorbing coupler which consist of two white plastic rings with 3 fingers each. These interconnect with a black rubber piece. Once of the white rings was cracked in half and one of the fingers was broken off. So that easy to figure out. I ordered a new coupling on partselect on Friday afternoon. On the next morning, Saturday, Fedex showed up with the replacement part. I was pretty amazed at the fast service since I only paid $7 for ground shipping. Anyway, I put the new coupling on and put the whole thing back together...we've run a dozen loads since without a hiccup. Beats dumpstering the unit or calling a repairman. I spent about an hour to take it apart and about an hour to get it all back together. You definately need a good socket set, screwdrivers. Good luck.

I actually didn't remove any of the panels. I tipped the washer at a 45 degree angle to the back and side to release the motor clamps, unhooked the power to the motor and removed the two drain pipes from the motor.

Once I had all of that removed, I was able to pull the motor away from the transmission and put the new coupling pieces on. The hardest part was holding the motor up (it is fairly heavy and cumbersome to hold while the machine is tipped like that). The pieces didn't go on too easily either. It would have been ideal to have at least the front panel off to use a hammer more easily. I did manage to get it on using a socket and a hammer. With some light taps it went on.

Next I put the hoses back on, the power, the bottom motor clamp, and then wrestled for another 30 minutes getting the top motor clamp on.

The clamps are the metal like springs that hook into the transmission and then spring tighten the motor to the transmission. Then there is a little screw that holds it in place... Not easy to see from any angle, and that is where having the front panel off would be ideal.

I've NEVER worked on a washer before and I accomplished this by myself in about 2 hours. I think if you are sure this is the problem, fix it yourself. Best 20 bucks and 2 hours I spent this month by saving a couple hundred on a new washer or repair person.

I used pliers to loosen the hose clamps and the small springs that hold the water pump to the water pump motor. The old pump then came off by simply pulling it off. The new was was the reverse. Everything worked well.
The biggest problem had been finding that the water pump was leaking. I first tried to fix it with epoxy but it is apparentlly made of nylon and the expoxy didn't stick well.
I am still annoyed that Whirlpool makes a water pum that leads so soon. The Whirlpool site showed my model number as non existent. Later, after purchasing the right one from this third party site, Whirlpool sent email that they found the model number and gave me a much higher replacement price for the pump.

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

snapped off the 2 springs on the water pump,took off hoses with pliers,took off the 2 little screws on the motor springs.snapped off the 2 springs on the motor,and the motor came off.took out the drive coupling,it just slides off...then reverse the procedure,and you are done...

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .