11018522791 Kenmore Washer - Instructions

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

Replaced motor starting capacitor. Noticed water leak at pump and replaced pump

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.

Removed the screws holding the control panel onto the washer. Removed the switch knob and then the switch (required unlocking a tab and then rotating the switch to remove). Unplugged the wiring connector and the water sensing tube. Replaced the switch in the reverse order and remounted the control panel. Test run proved the washer was working again.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

Popped the cap off the agitator (pocket Knife) Look down in the center of the agitator. I saw I needed a 7/16 socket, 6" extention and ratchet. I used 1/4" drive. I took the retaining bolt out and lifted the upper portion of the agitator off of the iower portion and out of the tub. Set the part I took out on the dryer. I pulled the cone shaped part that houses the 4 cogs pieces out of the center of the upper agitator part. Once the coned shaped part was out, turned it upside down and placed it on the closed washing machine lid, then again used my pocket knife to lift the plastic retaining ring that securely holds the 4 cogs in place upward on the cone as to remove and replace the 4 worn out cogs with the new ones purchased in a repair kit. Pay close attention the direction the old cogs are facing, so the new ones go back in the same facing direction. It can be extremely easy to install the new ones backwards. I have to say at this point, I was quite disappointed with the retrofit repair kit I purchased. The new cone part the holds the cogs and goes down into the center of the upper agitator wouldn't allow the bolt that locks the whole agitator to the shaft to line up straight and wanted the bolt to "cross" thread into the main shaft. I took it all apart again and reused the original coned shaped part that came with the machine. I should have purchased just the 4 cogs for considerably less money. Reassembled the cone part and put it back together. Reinstalled the upper agitator in reverse order of removing it. Turned on the washer and it works like it's supposed to once again. Hope this helps the next person.

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

After reading other repair stories I did it like they said. I disconnected all the hoses and drained as much water as I could. The top came apart easily with a regular screwdriver, a 1/2 in drive with extension, and a 14 or 15mm deep socket. The spanner nut came off easiest with several short, quick blows (punch and hammer, counterclockwise). In my case a good wack seemed to be soaked up by the wash tub springs. Be careful not to chip the tub.

I laid the washer, front down, onto a couple a 2x6's. I supported between the tub and body with small 2x4 scraps. The motor/trans/pump came off easily after disconnection the 2 hoses (towels handy) and wiring. After the 3 screws, and some wiggling, the assembly slid out nicely. The coupler came out after snapping the springs off to remove the pump and motor. A 1/4 nut driver and regular screwdriver assisted. Watch how the pump comes off. You might want to mark its orientation with a marker or something. Make sure you get the new coupler on all the way with some taps on the CENTER where the shaft is. Reassemble in the reverse order. You'll know why I suggested marking the water pump.

Watch the order/orientation of the springs, clips, and washer. The clips came off with a screwdriver and pliers. It's always nice to have a rag on them when removing, they like to shoot off and land in the spot that's hardest to find, like under the dryer. My clutch was assembled with the right spring and slid right on. Don't forget about the plastic washer, snap it in good. The plastic piece still on the washer was simple. I opened up a nose pliers and put it on each side of the clip then gave it a hit. It came off with minimal effort and didn't spin on the shaft like pushing on one side with a screwdriver.

During reassembly I put a very light film of grease on the shaft. That washer with the tabs gave me trouble at first. I put a good film of grease on the side with the tabs to hold it in place, with the tabs down, in the clip. Otherwise when sliding the assembly back together it comes loose and you won't get the motor/trans all the way in. Then it all has to come back out and you'll wonder what the heck is keeping the transmission from seating in all the way. You might even get it all together, figuring the motor or tub has to turn to get it to seat right. You may even try running a no clothes load and get stuck with a tub full of water. Ask me how I know.

Reverse everything to reassemble. Make sure you get the springs tight that hold the hoses on. I was worried about over tightening the plastic nut with a 1/2 drive. Run no-clothes load, large, hot with soap. I think tipping it over loosened some stuff that was stuck in between the tub and basket. No, it wasn't grease from the shaft, light film. Anyway, I'll waste a washer full of hot soapy water to avoid the, "Um..what's this on my new shirt".

I didn't mean for this to be so long winded, but I was leary about tackling this job at first. I know my way around the garage/cars, but never tried appliances before. I pictured it'd be apart for weeks and I'd have to call a repair man. Then the "I told you so" look would come. You all know what I mean. I just want to cover as much as possible and encourage others while having them avoid any troubles.

Followed direction that was sent to my e-mail. My washer timer would not advance. I' am so happy for the directions sent to me from this site and being able to get the part that I, needed from this site. I, didn't have and business doing the job myself, because I'm a ill 66 year old female. There's no special instructions that I, have to add. !! Thanks !! Lewis

Pretty much like shown in the video tutorial however I didn't disconnect the water hoses. I unplugged the machine and pulled it forward 6 inches. Took it apart like in the video but because of space restrictions I took the cabinet into another room to replace the switch and then re-assembled. The hardest part was getting the cabinet to re-seat as before. It took several attempts but it's all done and the machine is working like a champ. I listed a magnet because I use them to keep the nuts and screws from getting lost

On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.

The coupling, made of plastic and rubber, on our Whirlpool washer gave out. Done the same repair nine years ago and knew what to do. Here is a short summery:

1. unscrew the 2 screws that hold the control panel on top of the machine in place

2. unscrew the screws that connect the housing with the back panel

3. pop the 2 clips under the control panel to release the back panel

4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)

5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine

6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.

7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside

8. you can now remove the broken coupling

9. check for any fragments and clean off what needs to be cleaned

10. replace the coupling

11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!

12. test