79641172212 Kenmore Washer - Instructions

Followed the video instructions provided.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

remove the front part of the machine to get to the door hinge.

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC