79631423410 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- thomas m from CARMICHAEL, CA
- Parts Used:
- 4263FA3933C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
leg broke off inside housing
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from EDWARDS, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
very dirty under adjitator cap and pulsator
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Crystal Lake, IL
- Parts Used:
- AJU75152601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
During the spin cycle water continued to flow into the machine.
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from SIMI VALLEY, CA
- Parts Used:
- AEM73732901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drain hose had a pin hole leak external to washer
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from THOMASTON, GA
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
could not get the 10 mm nut to loosen
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Safford, AZ
- Parts Used:
- AGZ72909711, 5006EA3009B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DICKSON CITY, PA
- Parts Used:
- 6323EL2001G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine was displaying te code. Quick google search to diagnose the issue.
Very simple repair after watching YouTube video on how to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cathy. from etna, OH
- Parts Used:
- AEM73732901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
WATER WAS NOT SHUTTING OFF
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.
LOVE LG CHAT!!!
LOVE LG CHAT!!!
Was this instruction helpful to you?
Thank you for voting!