11022972103 Kenmore Washer - Instructions

Thank you for asking me how it went. the washer would not spin or pump water out, so I put it on its side and saw that the coupling was bad.
so I found you on the internet, thankyou very much, and put a order in for the part. well waiting for the part, I took the old coupling out it was easy, there was two metal bands one on each side of the motor took them off two bolts holding a plate on, and had old coupling in hand. and it was easy to put back with the new coupling. I enjoyed working on it. Dennis

It took me awhile to figure out how to get the shell off the washer frame. (I didn't know about flipping it on its back). Once the moving parts were revealed, the water pump was staring at me with both ports. I turned the machine on and saw that the leak was coming from the pump.
1. Cut power
2. unclipped pump with pry with screwdriver
3. detatched both hoses - flood ensued
4. gently pulled pump off transmission
5. replaced pump

I reccommend doing this repair with empty tub.

Second time I did this. Same repair about 4 years ago. Pretty easy. Take the cabinet enclosure off, take pump off, remove motor and replace the coupling. Since the coupling is now reinforced with metal, a little more difficult to get on the drive shafts of the motor and the clutch drive?. $20.00 saved me $500.00 for now with a relatively easy repair and hopefully with reinforced part, it will last a little longer.

This model is a compact / apartment size washer and the repair was fairly easy. The lid is held on by 2 spring clips on the front and 2 tabs on the rear. I used a screwdriver to pop the top off the clips, removed the screws on the tabs, unplugged the switch and set the top aside. Took out 2 screws (all screws are 5/16" hex head) on the left side panel (facing the front of the machine) and set it to the side. The pump is clearly visible at this point. Tipped the washer and propped it up for easier access. Removed the 2 hose clamps (set a pan underneath first) and the pump is held in place by 2 spring clips. Popped those off and the pump came right out. Put the new pump in, snapped the spring clips on, put the hose clamps back in place, the side panel and the lid. Not at all hard to do. About 30 to 45 minutes and I was doing laundry again.

Replacing the clutch was easy but unfortunately did not fix the washing machine. I couldn't get the agitator loose at first, but it came loose when I unbolted the motor and transmission assembly. After replacing the clutch and reassembling the motor, I tilted the washer back up and found that the basket in the center under the agitator was cracked all the way around and that was why it wasn't spinning. It was also why the clutch was burning--trying to spin a basket that wasn't centered in the drum anymore. This washer is over 25 years old, so I decided not to replace the basket, since a replacement is about $400. A good attempt at an inexpensive repair, but unsuccessful.

I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood first. Thanks.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

snapped off the 2 springs on the water pump,took off hoses with pliers,took off the 2 little screws on the motor springs.snapped off the 2 springs on the motor,and the motor came off.took out the drive coupling,it just slides off...then reverse the procedure,and you are done...

Unplug power cord. Turn off hot and cold water to washer. Disconnect water lines at the back of the washer, but mark which is hot and cold on the hoses . Remove drain hose from the sink tub or sewer line but keep it elevated so the water don't run out. Tip over on the backside but put something under the back side like a tool box to keep the top elevated a little bit, but not on the control panel just below it. Now remove the two screws that are in the motor retainer. Now pry motor retainers loose then lift out motor and remove old coupling. Now install new coupling. If it is a little tight on the shaft, use a deep socket a little bigger than the shaft to tap them on. Line up coupling while putting motor in place. Then snap on motor retainers. Look at the coupler make sure it is straight and not s shape. If it is s shape, remove and tap coupler on shaft a little more. If it is straight then reinstall the two screws you removed in the beginning from the motor retainers. Hook up drain line, water lines hot to hot, cold to cold. Then check for leaks on water lines. Plug in ,turn on, if it sounds ok. Don"t stand there, wash something.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.

First, disconnect from power & turning off the water. Then, accessed the part by tipping the unit back enough to work. Remove the hoses by loosening the spring clamps. Here is where things got a bit sticky. The pump motor shaft had corroded enough to make removal of the pump a wrestling match of sub-WWF levels. Once forced off, additional time was spent removing corrosion from the shaft to facilitate fitting the new unit. A little lube was used here. Re-assembly was quick & washer was righted, plugged in and returned to service. It is a simple repair which can, with a little acting ability, be portrayed as a monumental task requiring super-human strength & the wisdom of Solomon. I played the part well enough to merit a huckleberry pie for my effort & sacrifice! Thanks!

I used pliers to loosen the hose clamps and the small springs that hold the water pump to the water pump motor. The old pump then came off by simply pulling it off. The new was was the reverse. Everything worked well.
The biggest problem had been finding that the water pump was leaking. I first tried to fix it with epoxy but it is apparentlly made of nylon and the expoxy didn't stick well.
I am still annoyed that Whirlpool makes a water pum that leads so soon. The Whirlpool site showed my model number as non existent. Later, after purchasing the right one from this third party site, Whirlpool sent email that they found the model number and gave me a much higher replacement price for the pump.

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.