11074414210 Kenmore Washer - Instructions

My son did the repair. Thank God for Sons who know how to repair things. Worst thing was figuring out how to get the back off, top where dials are had to come off too. the rest was easy according to him..

I own a small, local handyman service as a Father/Son team. This repair is PERFECT for an apprentice to do as a confidence biulder. He learned the safe way to service a machine with garanteed success. This is a job anyone with basic knowledge can easily do with a little on-line homework on their machine. -Jim & Tom W.-

This was a thirty year old Kenmore washer. I removed the control frame, and then removed the two nuts holding the water inlet valve. The valve itself was easy, two water lines and one fill line. Reassembly was problematic as this valve was not exactly the same, I just tied off the valve to the water lines so it would not move.
Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.

Followed the instructions on the Part Select video which were very clear. I removed control module from top of washer, pulled the washing machine outer housing forward slightly and disengaged the rear closure panel slightly. I disconnected the electrical harness and then I was then able to remove the existing inlet valve. The new valve was then installed and the precess reversed to complete the installation.

Piece of cake!! (The water comes pouring into the machine now)

Opening the washing machine, and removal and replacement of the water inlet valve were both trivially easy. However, getting the cabinet back into place was a bit tricky, only because I did it by myself. It was surprising how flexible and flippy-floppy the cabinet became when free of the structure of the machine. It would have been a huge help to have had a buddy over to just help place the back corners of the cabinet into place. That would have made the whole job totally easy.

i removed all screws for back of washer and removed top washer controls. then removed the valves and replaced with new one. reinstalled back in reverse order.really easy job. you just have to pay attention how you took it apart and study how it works , thanks!

easy repair and so far so good stopped over filling so far hope this helps ... scott

replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

Removed backing and hoses and replaced the water inlet valve.

I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!

I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual

On this particular washer you have to remove the top part of the machine. Where your controls are at, ie: water temp, water level, etc. It takes removing a few screws. Than you have to remove the back of the machine. Unhook the washer hoses going into your machine. This is where your part is on the inside of the back. Remove the back by a few sliding hooks. Unhook the electrial plugins going into the mixer (value inlet). There will be other plugins you have to unplug up around the water level, water temp areas (on top of the machine). Remove the old water inlet value, replace it with the new. Replace all plugin electrical parts and put the back back on. Put top back on, screw in the screws and try your new machine. NOTE: When it comes to these electrical plugins its not that hard. They are are different, they can only go in one way. My wires were all tied together so each plug was at that particular plugin length. Ex: The last plugin was the longest. Pretty easy to know where it go. The other ones were shorter. In other words it was pretty easy to know where they went after unplugging. So don't be scared to try this. There is one wire that is screwed into the metal for a ground wire. Just make sure you do get this back in for your safety. It's the only one that could be over looked. I am a female and I watched and helped my loving father take this machine apart. After this I put this part in myself. I was amazed that my machine was like new again. I agreed to tell my story because by others telling there story is what helped me. It saved me from buying a new machine. When I seen the stories on this particular problem I was ready to take the chance. I had already spent way more than that at the laundry mat. Thank you again and best wishes to you all.

After my son received a repair quote of $130, I decided to help him and do the repair myself. I have replaced inlet valves before and ordered the part ($30) from partselect.com. I received the part in less than 2 days via regular FedEx. I used the Partselect installation video (very accurate) to familiarize myself on accessing the defective part. The job took less than 30 minutes. Unfortunately, it also took me another 30 minutes to clean out all the dust bunnies residing under, in, and in back of the washer.