11074414840 Kenmore Washer - Instructions

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

turn off hot and cold water faucets,unplug the power,pull washer out to gain access to rear cover, remove the top control panel screws,push back and lift off, disconnect hot and cold water hoses from inlet valve and remove enough screws from the back panel to remove the valve, disconnect the valve from the tub fill hose (mine had a spring type hose clamp) note the orientataion of the hot and cold hoses and the solenoid connectors for the hot and cold sides,(mine is stamped in the rear cover)reconnect and reassemble in reverse order and check for proper operation.

First, I unplugged it and disconnected the water hoses (the water has been off to it for days). Then, I tried taking off the back of the washing machine. This didn't work, and I actually ended up googling instructions and found pretty detailed, illustrated instructions at Popular Mechanics.
You need to unscrew the front panel that contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.

Putting everything back together literally just means reversing the instructions.

My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!

took off the rear panel and removed the existing inlet valve and installed the new one. Replaced the rear panel and the machine work better than ever.

i removed all screws for back of washer and removed top washer controls. then removed the valves and replaced with new one. reinstalled back in reverse order.really easy job. you just have to pay attention how you took it apart and study how it works , thanks!

I diagnosed by reversing the plugs on the hot/cold valves. I then removed the valve , cleaned it up and sprayed the electrical contacts with (Corrosion Block) and re-assembled. It still only had hot water. Ordered part, received part next day. When I went to install it I discovered that the (Corrosion Block) had penatrated and all was working! So now I have a spare valve.

Opened back panel and replaced valve - very easy

I removed the faulty valve after unplugging the AC cord. Two screws, the two water hoses were removed, and the electrical connections were unplugged. The old valve could then be rotated so that the clamp on the fill tube could be loosened and the tube pulled off the valve.
The new valve body seemed to be an exact replacement, but the mounting bracked was slightly different and required drilling two new screw-mounting holes; an easy job.
Before securing the mounting plate to the machine, the fill tube and clamp were reattached, and the electrical connectors plugged in. After connecting the supply hoses and plugging in the AC cord, the machine filled with water properly and everything seemed to be back to normal.
I might have been able to use the original mounting plate, but it had been taken to a different location which was too far away to easily retrieve.

I just followed the instructions from a previous customer. Worked perfectly.

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

Take top of washing machine off. Turn spikets off and remove hot and cold inlet hoses. Remove one screw holding part in place. Reach from front and take valve out. Unplug wiring harnesses. Reinstall the same way I took it off.

easy repair and so far so good stopped over filling so far hope this helps ... scott

replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.

removed top panel and back panel
and then disconect the two wire fromm water inlet
fallow by removing screws.disconect water hose
then put back new part make sure i have all same conected as original put back panel top and back
conected hose for water back and electric .
then i turned 0n cold water perfect work hot water perfect warm perfect. problem fixed.
thanks. pedro

First - I saw the picture of the part on your site. It made all the difference.
Then, I turned off the water supply, unplugged the washer, removed the screws holding the backing plate on the washing machine to expose the valve.
After that, it was as easy as removing two mounting screws, disconnecting the solenoids (just two connections), pulling out the old valve and replacing it with the new.
Pretty simple and a lot less pricey when you can wait a few days for a part to come in the mail.