VWXR4100TAAB Hotpoint Washer - Instructions

Easy as it gets. I did this repair while playing Wii with my 8 year old and cooking supper... Still no more than a 10 minute fix.

Place a towel on one side of the washer so you won't scratch it.

Tie a loop of rope around the middle of the agitator between the upper and lower fins. Wrap the other end of the rope around a 2x4 ( I used a level), or anything similar and wind it around until the 2x4 is pulled down level with the top, keeping one end on the towel.

Yank the other end firmly a few times, and the agitator will seperate from the coupling. I had to snatch it pretty hard.

I removed the 7/16" bolt from the coupling, pulled it off the spline and replaced it with the new one.

The agitator slid right back into place with no trouble, and it is good as new.

What seemed like an expensive repair, or even the need for a new appliance was essentially removing one bolt and a replacing a $6 part.

Thanks!

I removed the fabric softener cup and lifted up on the agitaotor till it slid off. I then removed the bolt that held the agitator coupling in place. I then worked the coupling off, wiggling it side to side until it slid off. Then I slid the new coupling on and replaced the bolt. Lined up the agitator and slid it back on. Then replaced the fabric softener cup. Job could not have been any easier.

Slide rope beneath agitator.
Pull up with good force..agitator will separate from coupling.
Remove screw from coupling.
Slide coupling off.
Slide on new coupling.
Install screw included with the new agitator (Don't use old screw. The new one is a specialty part designed for new coupling)
Slide agitator back down over coupling.
Done

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

easy to repair. instructions (with pictures) were included with the part. part came super fast.

Reaching into the washer I placed both hands on the bottom of the agitater 180 degrees apart and lifted the agitater straight up out of the tub. Using a 7/16 socket I removed the coupling kit. The new one slid right on. I secured it with the new bolt supplied with the kit. The agitater went right back on the new coupler and I was done. Fast, simple and inexpensive. Thanks so much to Part Select.

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!

first i removed the spindle and theni removed theplastic coupling

This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!

First, I removed the agitator by reaching in the washing machine and pulling up on the agitator until it popped off. Next, I removed the 1/4" bolt that attached the coupling to the spline. Then I removed the coupling. After removing it, I replaced it with a new one, installed a new bolt, and reattached the agitator. It took 2 days for me to get the part(ordered on a Sun)but only took me 10 minutes to repair.

I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.