VWXR4100TAAB Hotpoint Washer - Instructions

I just added the agitator coupling and screwed it in.

Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again

The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done

Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.

I was very disappointed that this washing machine was broken since it is the second GE washer I have had in this house and the home is only 11 yrs old. I went to the Parts Select website and used the repair information to diagnose the problem and order the part. The part was about $12 including shipping and arrived in a few days. Installation was quick and easy. Overall a very good experience since I was asssuming a broken transmission and new washer. Thanks Parts Select!

Popped the agitator off, removed the bolt, pulled coupler straight up. Reversed steps. Done in under 5 mins.

Agitator came off easily, but the agitator coupling was a little bit hard to remove. I have to yank it hard to be able to remove it. Putting the new part in is a bit hard too. I had to use a hammer to put it in. (with a piece of wood in between). Tried it with a small load and We're back in business. It was a pleasant experience to do business with you guys. Thanks for the quick turnaround.

I took the plastic agitator out and checked the agitator coupling underneath. I unscrewed the agitator coupling and looked inside. It appeared that the grooves on the agitator coupling which attaches to the stem had become stripped. I ordered the $6.00 agitator coupling and screwed it back onto the stem. The plastic agitator slipped back onto the coupler and it worked perfectly after that.

I reached under the agitator on two sides with my fingers and with one good upward yank the agitator came loose. I removed the agitator from the inside of the machine, I seen the Agitator Coupling was spinning in both directions so I felt that it may have been broken. I removed the one bolt hold the Agitator Coupling in place, I remove and inspected the Coupling and noticed that the spline was worn out. I cleaned the transmission spine that the Coupling slides over with a wire brush while using a shop vacuum to catch any loose debris. I installed new Agitator Coupling Kit slipped the Agitator back inside the machine over the coupling and pressed it down until it snapped into place. Job done. Machine works great.

pulled agitator off unscrewed bolt holding coupling on put new coupling on bolt in place put agitator on. washer working good

To get the old agitator off I first used two pieces of laundry line rope to hook under the fins of the agitator on each side. Next I laid a 5 foot long 2 X 4 across the top and tied the ropes on. I filled the washer with 5 or 6 inches of extremely hot water to help loosen everything up and used leverage to pop the old agitator off. After that I used a socket set to remove the bolt from the top of the agitator coupling and took it out. I then put the new coupling in, replaced the bolt and lined up the agitator and slid it back on until it clicked and locked into place. The washer works great.

My husband remove the agitator and found that it was worn. I googled the problem and one of the websites that came up was PartSelect. My husband watched the easy to follow video and had me order the Agitator Coupling Kit. It arrived in just two days. It took him 15 minutes to install and I started washing immediately. It cost us $13.22 and saved us $800 to $1200 if a new washing machine would of had to be purchased. The washer is 15 years old and now with this repair will hopefully continue to wash for a few more years! Thank you PartSelect!

I noticed that the agitator would spin without any resistance and must be stripped. I pulled the agitator straight up and it came right off. I then used an open end wrench to remove the bolt securing the agitator coupler to the metal spline. It came right off and was obviously stripped. Upon receiving the new coupler, slipped it straight on and tightened the coupler. Placed the agitator on the coupler and tested the washer, it worked. Very easy. My wife was ready to buy a new washing machine and I fixed it with a six dollar part.