HTWP1400F1WW Hotpoint Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harwinton, CT
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mabry from CLINTON, MS
- Parts Used:
- WH43X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Agitator was broken
First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from FLORENCE, KY
- Parts Used:
- WH41X10096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Eldom, MO
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from Bynum, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Port Hueneme, CA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from ROCHESTER, NY
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace drive belt on washer
I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Spring city, PA
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bad lid switch
Watched the how to video, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from SAN MATEO, CA
- Parts Used:
- WH13X23974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water continued slowly running into washer when off
I have never done this repair previously, and it was simple and easy, but I didn't know that until I watched your video. Several days after placing the order for the part, it came & I followed your video instructions, and voile! Washer works like new again. I can't thank you enough for your video instructions & making all these parts available. PLEASE keep it up!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from BERKLEY, MA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Plastic pipe developed a tear and leaked drain water.
Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from State College, PA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
Was this instruction helpful to you?
Thank you for voting!