VVSR1040V1WW Hotpoint Washer - Instructions

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.

removed agitator unscrewed agitator coupling replaced with new one replaced agitator

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

This top loading washer was purchased new in 2006. It has had a good bit of use and was a rather inexpensive model, but had been working fine. Suddenly the agitator stopped working. First I pulled off the agitator inside the machine, which in this model came off in one piece. In order to do that I grabbed it at the very bottom by pushing my fingers underneath the base, then rocked it from side to side while pulling up on it until it popped off. This exposed the agitator gear that had gone bad. I unbolted the gear and pulled it off. This removal took a bit of effort, and again, we had to rock it back and forth while pulling up on it until it finally came loose. When the new part arrived a few days later, we slipped it onto the transmission stem, and bolted it into place. Then the agitator was put back on and snapped into place. Works as good as new for less than $14, including shipping!

Took off old agitator, removed coupling that was bad and put new one on.

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

Removed fabric softener cover by pulling up. Then removed agitator by grabbing at the bottom and pulling up. Note I did read online that some may have a bolt holding the agitator down thats what it seemed like when I read it. Mine did not have a bolt. after removing the agitator there is a 10 or an 11mm bolt holding it down remove that and the coupler comes right out then install in reverse order. All done. Also its a ge adora washer.

I did this by myself and it was so easy. I'm a tiny female so it didn't take a lot of muscle and I only got one bruise :) I pulled the agitator off, there was no screw holding it in place. Removed the screw that was holding the coupler on with a socket set. Put the new coupler in place, used the socket set to screw it on, popped the agitator back on and crossed my fingers.....It worked like it was brand new. So happy, apparently the old coupler was stripped out. Super fast shipping and I will come back for other parts as needed. Thanks so much!

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

First I had no idea what to do. My first thought was to buy a new washing machine and so I began searching and found that a washer equal to mine was over $600. I brewed on this for a few days when a neighbor told me that they are not that hard to work on and we should take it apart and look at it first. We took the top and the front of the washer off and looked at the belt and the motor. All seemed fine. (we just used a screwdriver for that) then we took the agitator off, it pulled right off with some heavy tugging. then we saw the coupling. It was only held on by one screw. We used a socket to take the screw out and pulled the coupling off. It is supposed to fit very tightly on a shaft with gears. When we pulled it off and looked inside it, all the plastic gears in the coupling were stripped and that is why the agitator would not move. I expected this to cost me at least $50, but to my surprise the part was only $6.50. The shipping cost more than the part. When it arrived in about 3 days. I literally had the part on and the washer back together in less than 5 minutes. The entire repair cost me $14 and now the washing machine works better than it has worked in years. Who knew. If you intimidated by working on washers, don't be, they really are very simple machines and so not worth calling a repair man for.

Found out the screw was stripped from the agitator, probably because the washer is over 10 yrs old. We got the right part! The parts store was very fast in shipping, in fact we got it the next day! Highly recommend PartSelect!!!!!!!!!!

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

I had no intention of trying to fix the washer myself after reading about how to do it, only because I didn't know what half of the words were referring to. But once I watched the video, and I saw that the part was going to cost less than $15.00 (shipping included), I thought I would at least try it before going out and buying a new machine. The washer in the video was slightly different than mine, but I recognized the parts from my machine and mine was actually easier to replace than the one in the video. I just pulled off the agitator, unbolted the old agitator coupling and replace it with the new one, bolted it back on and lined up the agitator grooves with coupling and that was it. It worked and saved me a lot of money. I once had an appliance repairman tell me that if your washer or dryer lasts 7 years nowadays, you should consider yourself lucky. Mine is 7 years old, so I thought I would have to replace it. I didn't particularly want to pay someone $100.00 to come to my house and tell me it couldn't be fixed if I was going to have to buy a new one. But fixing it myself was very easy. Written instructions never would have worked for me, but the video was very helpful. Thanks!