WDSR2080GC General Electric Washer - Instructions

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

followed instructions on you-tube. shut off water faucets. disconnect hoses from washer. remove three hex screws from back of control panel. lean panel forward and slide to the right, then remove it and lay it down.
remove the two screws that hold the valve to the machine. use pliers to slide the clamp back and remove the hose. repeats these steps in reverse to finish job.
the first valve that partselect shipped leaked from the hot water hookup and was deemed to be defective. partselect credited my account before the part was at their warehouse. great service all around.

The pump arrived and because I'd read some of the other stories here I wasn't too upset that it looked different.

I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.

The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.

Removed front cover, disconnected wires and hoses, reversed process

after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.

Replaced pump. New pump same manufacturer and model, but better built; however, base plate not same, requiring that I swap it for the original. Also, pump suction inlet is straight-in, whereas original has 90 degree connection. Disconnect power, and remove old pump. Purchase a 1 1/2" I.D. auto radiator hose, cut off use the 90 degree bend; it's a perfect fit to pump conn.; use a 1" PVC coupling on other end socket to mate to the washer drum convoluted drain hose socket. Throw away the crappy original G.E. hard-to-use spring hose clamps and use stainless steel automotive type gear clamps instead. WARNING: Do not try to bend, stretch, or kink the rubber tub drain hose to fit up to the pump without installing an elbow; the installation geometry must be exactly the same as the factory-designed installation. To finish the job, power up and run the machine through several cycles with the front cover off to check for leaks. You will also see why the rubber drain hose must be reinstalled as described above. This washer does not ramp down speed when in the spin cycle, and when the motor stops, the drum makes a sudden 15 to 30 degree rotation, stretching the drain hose to it's limit. Finally, keep your hands out of the machine when it's running; the motor, belt, and transmission drive can cause some real damage if you get tangled up in them. Pay attention to what you are doing; if you are confused by my little dissertation, hire someone qualified to do the job for you.

The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.

Repair went great. The large nut had to be soaked to free it but the part was an exact fit.

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

My washing machine would not agitate. I looked online for the possible repair solutions under GE website. All I needed was my model number. I typed in the model number and it gave me possible solutions. I ordered the parts from part select. Once they came in, I then went online to find video of how to repair the machine. When I found the video I needed I began disassembling my machine. I pulled the agitator off with a brisk tug and used my socket wrench to unscrew the coupler nut. Once that was off, I installed the new coupler tightened the bolt and installed the agitator. I filled the machine enough for a small load and sure enough, it worked! I did not need to use the belt, but I will have it on hand if I need to. I saved on separate shipping. VERY PLEASED!

I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.

So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!

watched Partselect video and followed instructions step by step

If you follow the video that part select provides you will be just fine.