WBSE3120B2CC General Electric Washer - Instructions

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.

So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.

Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.

I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.

PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4

As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!

front back and top have to come off, but contrary to 'youtube' instructions, 'nothing' has to be disconnected, if the washer is pulled away from the wall and power unplugged things can be unscrewed and pushed back enough to pull the inner tub out and get to the seal without disconnecting water lines wires or anything else.. the main shaft nut is aluminum and the shaft is 'castellated' so alittle penetrating oil on it and a short 10" pipe wrench in conjunction with a 2lb sledge busted it loose easy enough so i didnt need to buy a spanner .. the seal was easy to get out with a couple of screwdrivers wedged in the sides .. the old split ring crumbled upon removal also so get one of those .. i lucked out on the washer that goes with it and mine was still usable but if it was rusted any more than it was i wouldve needed that also .. so good idea to get the 3 items if your doing the seal - seal, split ring, and washer - another thing, i cleaned everything up good, knocked everything off with a brass brush, polished the shaft seal area with some 600 grit and then lubed the seal with silicone grease thinking it might be hard to get in .. it wasnt .. and it leaked slightly until i did several loads .. in hindsight it would be better to 'lightly' coat the outer edge of the seal that mates to the tub with a good silicone gasket maker, the inner lips with the grease would be fine ... so thats about how it went, parts came quick and i had it all fixed up in a couple of hours .. cleaning things as i went probably took longer than the wrenching ..

Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.

Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.