EJRR4170E4WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laura from Woodbridge, VA
- Parts Used:
- WH01X10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
On Friday the 13th, after spilling my coffee all over the table, I put the tablecloth in to wash. When I pulled the tablecloth out of the washer & put it into the dryer, I must have been angry at myself because I wrenched the dryer "Start" knob too hard & broke the knob off! I spent a few minutes looking for the part, and found that PartSelect had exactly what I needed at a very reasonable price. Once ordered, I received order confirmation, and, amazingly, the part arrived at my home in less than 24 hours after I broke the knob! Thanks, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Oxford, GA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Purchased used washin machine w/o drain hose
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Lake Forest, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Washer won't drain water
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Roslyn, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer tub was making loud noises.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Old Lyme, CT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Pump went bad, machine had very little use would not buy another GE washer
Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Timberon, NM
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
broken belt
It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gigi from Monroeville, PA
- Parts Used:
- WH43X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was no fabric softener dispenser
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from New Albany, IN
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Timer knob had broken
First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Henderson, NV
- Parts Used:
- WH12X10498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No cold water in any cycle.
Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Ephrata, PA
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer would not spin
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from MESA, AZ
- Parts Used:
- WH02X10383, WH02X10265, WH2X1199, WH2X1198, WH2X1197, WH2X1193
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Water leaks on floor in front of machine.
Worse machine ever made. Installed all parts per videos .they helped a lot. Inner tub went on crooked and first wash ruined inner/outer tubs top piece. Took to dump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from KELLER, TX
- Parts Used:
- WH12X10462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Capacitor failed (cracked, split, and melted a little), washer would not spin and laundry room filled up with smoke
Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Talihina, OK
- Parts Used:
- WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water leaking from filler hose outside of tub
removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUPESH from BELLFLOWER, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water was leaking from machine.
Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.
------Got chicken and beer that Sunday--------------
Replaced pump on Sunday and leak was gone and wife was happy.
------Got chicken and beer that Sunday--------------
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles Wayne from Forest Hill, WV
- Parts Used:
- WH41X10096
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Hose would not seal at rear of washer.
The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.
Was this instruction helpful to you?
Thank you for voting!