CCXR1060B3WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Katy, TX
- Parts Used:
- WH12X10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
washer overflowed while running
First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald L. from Las Cruces, NM
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Waher would not spin wet clothes.
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Chilhowie, VA
- Parts Used:
- WH02X10265, WH2X1199, WH2X1197, WH2X1193, WH1X2026, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
transmission leaking grease
removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Benton, IL
- Parts Used:
- WH49X10042, WH43X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator stripped
removed the old one and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Perrysburg, OH
- Parts Used:
- WH13X10024, WH41X10096, WH16X513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Overflowing washer
Unplugged the washer and unscrewed the hot and cold filler hoses from the back of the machine. Removed the 6 screws holding the top together. Unscrewed the 2 water valve mounting screws. Pulled off the electrical wires from the leads. Unclipped the water feed hose clip. Reattached everything to the new water valve in reverse order. Put the screws holding the top panel in place back in.
For good measure, I also replaced the drain hose since I had noticed a little leakage there. Two screws and a little twisting and pushing was all that took.
Then I hooked everything back up and it worked like a charm. Finally, I went out to dinner with my wife on the money I saved!
For good measure, I also replaced the drain hose since I had noticed a little leakage there. Two screws and a little twisting and pushing was all that took.
Then I hooked everything back up and it worked like a charm. Finally, I went out to dinner with my wife on the money I saved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Oxford, GA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Purchased used washin machine w/o drain hose
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Roslyn, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer tub was making loud noises.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Old Lyme, CT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Pump went bad, machine had very little use would not buy another GE washer
Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Timberon, NM
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
broken belt
It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Lake Forest, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Washer won't drain water
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lapeer, MI
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Ephrata, PA
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer would not spin
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from KELLER, TX
- Parts Used:
- WH12X10462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Capacitor failed (cracked, split, and melted a little), washer would not spin and laundry room filled up with smoke
Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Pylesville, MD
- Parts Used:
- WH12X10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water everywhere - overflowing washer
We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelby from Binghamton, NY
- Parts Used:
- WH12X10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water Overflow
1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod
Was this instruction helpful to you?
Thank you for voting!