Models > WSM27TCBWWW > Instructions

WSM27TCBWWW General Electric Washer - Instructions

Jump to:

All Instructions for the WSM27TCBWWW
76 - 90 of 163
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
DOUGLAS from CHILLICOTHE, OH
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
clothes get stuck and burn in upper drum glide
Found the promblem as described at this site while looking for diagrams for the dyer. Repair went as described. Once I removed the old upper drum glide I used acetone to remove old glue. Cleaned up fast and easy. Once installed I let cure for about an hour and then reassembled. Let it cure for about an hour more and then I used the dyer. I could feel that the gap around the front of the drum was again narrow so that my finger tip would not slide into a grove. So far so good.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
STEVEN from HAMPTON, GA
Parts Used:
131461200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
the drain hose was leaking
i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbra from Mills River, NC
Parts Used:
131858004
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Off/on knob broke
Pushed the new knob into place.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from Parker, TX
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Zippers and other items on clothing getting stuck in drum.
Followed the instructions in the video. It was very helpful.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keelyn from Old Greenwich, CT
Parts Used:
WE01X10160
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The knob that came with the unit was broken
I took the serial and model # off the appliance, located it on your site, purchased it and it was sent within 2 days. Thanks! I think the old one was a defective one because it never worked.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
guillermo from los angeles, CA
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
drum turning out of balance, due to worn out drum glide top and bottom, and clothes being cougth beteween dryer frame and drum
I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BRAD from Vancouver, WA
Parts Used:
WE03X29897
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
turned switch to run but dryer wouldn't.
I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from spring grove, IL
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
cloths getting caught between drum front cover
1)Unplugged unit from out let 2) Lifted top cover from base by prying up from the from the corners back is hinged 3) removed wires for door switch , removed a screw on the left and right from front. 4) pull front cover out from the top untill it clears drum then lift straight up off bottom clips. 5) scrape off old felt strip and guides 6) Sand untill all felt residue gone apply new glue to front cover wait a few minutes for glue to get tacky 7) clean out all the lint build up Checking from time to time that guide assemble is in place on front cover. 8) reinstall front cover when glue is dry.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from charleston, SC
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
cloths getting stuck between drum and front panel
repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from Merrick, NY
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set
Washer needed back bearing & drum guides
Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Tomahawk, WI
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
clothes getting caught between drum and front of machine leaving rust marks
* Clean off top of stackable dryer and remove top lid (pops off w/ screwdriver)
* Disconnect power supply and control wiring (right side under top lid)
* Remove left and right single screws securing front face of dryer
* Pop off dryer face w/ screwdriver
* Remove existing top glide from dryer face (peels off, use screwdriver or chisel/scraper to remove residue from felt and glue)
* Test fit new top glide
* Apply adhesive (included) to dryer face rim
* Clamp with 4 or so spring clamps and allow adhesive to set up (I waited about 30 minutes).
* Clean and inspect inside of dryer while the front face is off
* Clean dryer vent assembly (attached to dryer face)
* Reassemble and test easy rotation of the drum prior to use
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donnie from Nacogdoches, TX
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The dryer has a squeal that got worse.
Pulled the dryer front off to expose the problem. Thought it had a bearing of some type. Went to the PartSelect web site and watched the repair video. The Tech explained everything needed to make the repair. Ordered the parts kit and it arrived in three days by FedEx. Followed the directions. Simple. The video was excellent and made the repair a snap. Thanks.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from Alexandria, VA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer wouldn't turn drum
Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sean from nesconset, NY
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Dryer wouldn't spin
I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Bantam, CT
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
clothes were getting stuck in crack between drum and front wall of dryer
I ordered parts, recieved in 2 days. came with upper glide, glue and instructions. instructions were easy to read and follow. I used the wood chisel to remove old felt, cleaned well with some solvent, reap[plied glue, wait a few minutes , apply felt - reassemble dryer - viola- done. very satisfied customer
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WSM27TCBWWW
76 - 90 of 163