WSM27TCBWWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Portsmouth, RI
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer squeak during tumbling, worn front drum glide
Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.
A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.
Fit of new glide was straightforward and fit well to the lower felt glide..
(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.
Fit of new glide was straightforward and fit well to the lower felt glide..
(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brandon, FL
- Parts Used:
- 131461200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water leaking from bottom hose
remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSANNE from CENTRAL ISLIP, NY
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had dropped the dryer filter in the washing machine
the repair was completed with a new lint filter. easy in, the old one tossed out.....perfect/ i'm amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carroll from Rockaway, NJ
- Parts Used:
- WE01X10160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not use dryer time knob so could not dry clothes
Merely replaced the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from SILVER SPRING, MD
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was damaged.
Took a chance on the size and luckily filter was perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from ROCKAWAY, NJ
- Parts Used:
- WE16X29397
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dyer lint filter had holes in the screen
Just installe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth C. from Fort Valley, GA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clothes getting stuck in dryercausing brown stains on clothes
Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from EDISON, NJ
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our Clothes Would Get Caught In Between The Drum & The Front Cover, Making Marks On The Clothes.
I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Batesburg, SC
- Parts Used:
- 5303207102
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
strike broken
popped in one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from Dallas, TX
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The clothes was getting stuck on the tumbler
First I removed the 2 screws on the back. These 2 screws hold the top cover. I also used a flat screw driver to press the 2 locks that hold the top cover, they are located in front and under the top cover . Then I removed the 2 screws that hold the front cover. After removing the front cover I replaced the drum glider and the seal-basket lower. Now my dryer is working perfectly...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arne from Nome, AK
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty streaks on clothes.
I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- toshio from canton, GA
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was burning clothes
There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Smyrna, TN
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer leaving brown spots on clothes
First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Plamen from Alexandria, VA
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
screeching dryer
Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!
Was this instruction helpful to you?
Thank you for voting!