GBVH5140H0WW General Electric Washer - Instructions

The repair video was almost perfect. I would not have even attempted the repair without the video as I am not a handyman at all. The diagnostic feature based on the symptoms was invaluable. I originally took the front of the washer off because I thought the rubber seal around the door was leaking.It was like 67% of the problem. But after checking the front seal carefully, I determined it wasn't. The next most likely issue as only rated 19% but when the water inlet pipe, I was actually tickled to see a crack in the plastic pipe. I ordered on line on Monday and with the cheapest shipping, I received my part in the mail on Thursday. I would highly recommend using Part Select for diagnostic, parts and repair. I will definitely use again. If I could make one recommendation to Part Select, it would be to do a close up during the video when the technician is working with a part, i.e., the wiring that goes around the rubber seal.

I won't bother repeating other people's comments. My repair took a bit over 2 hours. I watched 2 different videos and thought the repair was doable. To remove the first wire band holding the boot seal to the front panel I found using an awl to grab the eyelet near the spring was easier than using a needle nose recommended in the video. To remove the second wire band I used an offset screwdriver. One video I watched recommended removing the lower counterweight to get at the band's screw - I did not do that. Putting the new boot seal into the first groove and installing the wire band was the most time consuming part of the job. I did not have extra hands to help. I recommend the second pair of hands for that part to save time. The rest of the install was easy.

followed partselect video instructions. Easy but takes time. Thank you

removed screws took off the old parts and put them on the new frame. the hardest part of the job was waiting 5 weeks for the part

Watch the video posted on PartSelect. It was excellent and walked step by step through the whole repair.

I only ran into one issue not included in the video. In order to remove the inner ring holding the boot seal, I had to remove the weight at the bottom of the tub. This is easy to remove with a wrench, but took two people to reinstall. You only need the second person for 1-2 minutes to hold the weight while you align the bolts.

The most difficult part is ensuring you replace the hex nuts and screws in the same location. I took pictures as i removed them to know where to reinstall.

Total repair time was probably 1.5 hours.

Before disassembling anything be really sure that the little things are reassembled just as they were prior to removal.....

My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! Hook up the drain hose with pliers and screw the motor to the frame and that's it!

After getting error message from washer, Looked it up and found if the water lines are find, then replace the water valve. After replacing the valve, everything works fine.

Unplug the machine. Remove the 4 screws on the back panel of the washer. Loosen the tub pulley bolt. Remove the old belt (mine did not completely break, it was shredded and slipped off the pulley). Replace with the new belt. Tighten the pulley bolt. Put the back panel on. Plug in the washer. It is working like new. :)

All i did is pull the front panel off,then n removed the front clap with channel locks then the side clamp the same way.i then removed the main clamp with a Phillips screwdriver very simple not ever 15 minutes to do

You probably won't want to publish this but it worked. The baffle on the GE washer I have required a complete tear down of the machine's front and outer waterproof drum to get a tiny little screw out. Very poor design if you ask me. And, I was not about to pay a technician for a massive overhaul to get a 3/8" long stainless screw off the broken remains of the baffle. So, I measured how far over the screw was from the pipe that feeds detergent, softener and bleach into the drum. I drilled a 3/8" hole in the outer drum. After removing the screw and installing the new baffle (which took all of about 2 minutes), I put a 3/8" hole plug I bought at Lowes into the hole with two part plastic epoxy. Then I covered the entire hole plug with a crown of epoxy. Five minutes later when the epoxy set, I ran a load of clothes. It ran perfectly and did not leak. I know. I know. This is not what you would recommend to your readers but it worked. I was brought up fixing everything around the home and any effectie shortcut was/is used. Oh,by the way, if you know which GE engineer thought up the design for this baffle installation, whack him on the head once.

VERY simple, just took two philips screws off of the door, replaced the broken part, put the screws back in! LOL

removed the spring-loaded ring around drum seal, removed old lock latch, and installed new lock latch. also, removed old door plunger and installed new one. then re-installed the spring-loaded ring lock around the seal. there were 5 screws and 3 electrical plugs that were easy to remove and re-install. note: i used a black sharpie to mark where the original door plunger was prior to removing the original.

Any repair should go easily if you have the right tools and the right PARTS. Like the before mentioned and all went well. The hardest thing about this particular water leak is identifining were the leak is. These parts are on the top of the washer. Take the top off and whamo there it is the cracked fill tube and smashed to hell washer. Real easy to replace. BUT that is really putting a band-aid on the problem. To me this washer was poorly designed by GE. Washer sits on a thick rubber mat, which sits on a conrcete floor and still jumps around, mainly when towels are in it.Fix that problem and then replacing these parts is a one time deal.

hold drive pulley from turning and used socket wrench to remove nut. then pulled off pulley from shaft and belt came off same time. very carefully filed the flat sides of the shaft end where the pulley slides onto. careful not to overfile or round out the she shaft end. carefully tap in place the pulley onto the shaft. install a new nut and tighten it approx. 40 ft pounds or 1/4 turn past tight. do not reuse old nut. pulley comes with a new one and the nylon on the old one is no good once used. once pulley is tight install the belt first onto the motor shaft then work the other end of the belt onto the pulley from top end then turn the pulley wheel counter clockwise as you push more belt onto the pulley wheel. kind of like putting on your bicycle tire on your rim.