GJSRP080D5WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Ephrata, PA
- Parts Used:
- WH11X10033, WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
teeth were stripped on dial
Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from NORWALK, CT
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Old Knob Broke.
I replaced the old knob with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Oxford, GA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Purchased used washin machine w/o drain hose
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Tampa, FL
- Parts Used:
- WH16X544
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer tub fell sideways
Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Roslyn, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer tub was making loud noises.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Old Lyme, CT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Pump went bad, machine had very little use would not buy another GE washer
Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gigi from Monroeville, PA
- Parts Used:
- WH43X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was no fabric softener dispenser
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lapeer, MI
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Lake Forest, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Washer won't drain water
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Timberon, NM
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
broken belt
It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Henderson, NV
- Parts Used:
- WH12X10498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No cold water in any cycle.
Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Ephrata, PA
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer would not spin
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from MESA, AZ
- Parts Used:
- WH02X10383, WH02X10265, WH2X1199, WH2X1198, WH2X1197, WH2X1193
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Water leaks on floor in front of machine.
Worse machine ever made. Installed all parts per videos .they helped a lot. Inner tub went on crooked and first wash ruined inner/outer tubs top piece. Took to dump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Lewiston, ID
- Parts Used:
- WH11X10033, WH01X10310
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The edge of the knob wore out
I pulled the old knob off and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from KELLER, TX
- Parts Used:
- WH12X10462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Capacitor failed (cracked, split, and melted a little), washer would not spin and laundry room filled up with smoke
Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!
Was this instruction helpful to you?
Thank you for voting!