GCVH6600H0MS General Electric Washer - Instructions

You probably won't want to publish this but it worked. The baffle on the GE washer I have required a complete tear down of the machine's front and outer waterproof drum to get a tiny little screw out. Very poor design if you ask me. And, I was not about to pay a technician for a massive overhaul to get a 3/8" long stainless screw off the broken remains of the baffle. So, I measured how far over the screw was from the pipe that feeds detergent, softener and bleach into the drum. I drilled a 3/8" hole in the outer drum. After removing the screw and installing the new baffle (which took all of about 2 minutes), I put a 3/8" hole plug I bought at Lowes into the hole with two part plastic epoxy. Then I covered the entire hole plug with a crown of epoxy. Five minutes later when the epoxy set, I ran a load of clothes. It ran perfectly and did not leak. I know. I know. This is not what you would recommend to your readers but it worked. I was brought up fixing everything around the home and any effectie shortcut was/is used. Oh,by the way, if you know which GE engineer thought up the design for this baffle installation, whack him on the head once.

All i did is pull the front panel off,then n removed the front clap with channel locks then the side clamp the same way.i then removed the main clamp with a Phillips screwdriver very simple not ever 15 minutes to do

Removed top and front control panel. Shut off water, disconnect water lines at front and dispenser. Remove dispenser. Remove water inlet pipe by pulling out of boot. Install new pipe.Reverse proceedure. Note, these pipes may tend to split on the bottom.

Removed top cover, loosened front door cover, removed & replaced old cracked plastic 'water inlet tube', reinstalled front door unit & top cover. Very tight space to work in when not completely removing front door unit.

I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.

This is the second door boot seal that I've replaced on my GE Washer (I don't know the model number). I turned on my IPad, went on YouTube, and found this video: "GE Front Loader Washer Gasket Replacement." I placed the IPad on top of the dryer which was right next to the washer and followed the instructions step by step. I used the pause and play buttons repeatedly to ensure I followed the instructions correctly. The hardest part was placing two retainer rings back on. These retainer rings are used to attach the gasket to the washer drum and to the door opening. When the door is closed it effectively seals the drum preventing water from spilling out or leaking. Before reinstalling both rings, ensure that the gasket is properly seated inside the appropriate grooves on the drum and the door opening respectively. It’s a very tight fit between gasket and metal, so you have to make sure the gasket is properly seated all the way around. The inside retainer ring can be tighten with a Philips screw driver or a small wrench. Not as easy as it sounds because you don't have too much room to work with. I had to grab the drum on the right side and tilt to the left in order to get a little more room for my screwdriver. It may be easier with a small wrench, but I don't have the patience. The second retainer ring goes on the outside of the gasket and the door opening. This ring is spring loaded. Attempt to place as much of the ring inside the groove before the spring loaded tension prevents you from going any further. When you get to this point, take a flat tip screwdriver (careful not to damage the gasket) and hold the retainer ring in place while moving counterclockwise and with a second flat tip screwdriver stretched the ring and popped into place until the whole ring is in place. The guy in the video does this effortlessly with only his hands. The first time I did this, my wife helped me do it. She held the left side while I used two flat tip screwdrivers to stretch the ring, pop in place, hold, stretch, and pop in place until complete. Once you're done you will feel good about yourself and grateful to the gentleman who recorded the video and was nice enough to share. Good luck.

1) Remove door hinge cover. 2) Remove hinge door plate. 3) Remove hinge door pin using a hammer and striking tool if necessary. 4) Using needle nose pliers, remove gasket inside clamp from the door boot seal. There is a spring at the bottom that should allow you to pry this part out and off. 5) Pull the door boot seal away from the exterior cabinet to allow access to the hinge. 6) Remove the hinge screws 7) You should now be able to remove the hinge. 8) Install new hinge and reverse steps to reassemble.

After looking at the video on how to repair a door boot seal on a Front Loader Washer. I went about installing the new boot seal, but after it still didn't fit in place correctly, I glanced over the top and noticed and after a few minutes noticed that one of the suspension springs was broken and the drum had dropped quite a bit. I ordered the spring I believe it was part 204 and in a couple days I and my father got the spring in place and now the washer is working as good as new. As it turns out I didn't need the door boot seal after all so now I have a backup incase one fails.

Any repair should go easily if you have the right tools and the right PARTS. Like the before mentioned and all went well. The hardest thing about this particular water leak is identifining were the leak is. These parts are on the top of the washer. Take the top off and whamo there it is the cracked fill tube and smashed to hell washer. Real easy to replace. BUT that is really putting a band-aid on the problem. To me this washer was poorly designed by GE. Washer sits on a thick rubber mat, which sits on a conrcete floor and still jumps around, mainly when towels are in it.Fix that problem and then replacing these parts is a one time deal.

hold drive pulley from turning and used socket wrench to remove nut. then pulled off pulley from shaft and belt came off same time. very carefully filed the flat sides of the shaft end where the pulley slides onto. careful not to overfile or round out the she shaft end. carefully tap in place the pulley onto the shaft. install a new nut and tighten it approx. 40 ft pounds or 1/4 turn past tight. do not reuse old nut. pulley comes with a new one and the nylon on the old one is no good once used. once pulley is tight install the belt first onto the motor shaft then work the other end of the belt onto the pulley from top end then turn the pulley wheel counter clockwise as you push more belt onto the pulley wheel. kind of like putting on your bicycle tire on your rim.

Followed your instruction, very easy. I installed Camco 90" & 45" Brass elbows to relieve strain on hoses.

I watched the video and followed the instructions. First remove power. Remove the rear cover from the control panel and the top cover. Then remove screws that secure the control panel to the frame and remove the control panel. Remove the bottom cover. Then remove the lock ring that holds the rubber boot to the front panel. Remove the door and remove the water inlet pipe. Assemble the machine and run a test cycle.

I followed the instruction on your site. I disconnected the power to the washer turned off the water turned on the nearest faucets to drain the lines. I removed the water hoses from the machine then took the three screws out of the back at the top of machine that held the lid on then removed the three screws on the top of the lid that hold the plastic piece to the front panel and pushed the lid toward the back and it lifted off. I then took the metal ring clamp off the water line attached to the water inlet valve and took the screw out that is on the back of the machine holding it on removed the wire plugs one at a time and put them one at a time on the new inlet valve so I would not get them mixed up. I then put the valve in place reconnected the water hose and metal clamp put the screw in the back to reattach valve the machine put the lid back on in reverse to removal reattached water hoses to the inlet valve turned the water back on plug in the power and immediately used the machine which works like new 20 minute job from beginning to end. By the way ladies if I can do it you can do it. TC

Step 1- pull washer away from wall. Step2- unplug power, shut off water and disconnect lines, and disconnect drain line. Step 3- unscrew 3 screws from bk and 3 screws from behind control panel. Step 4- remove back of control panel and top of washer. Step 5- unplug wires from old valve and plug into new valve to avoid wrong connection take out screw from back releasing old valve , insert new valve and put back screw. Step 6 put top of washer and back of control panel on and insert screws. Step 7- reconnect hoses and drain , plug washer in and test. All done. I recommend adjusting to level if necessary at this point before pushing back against wall. Good luck. Hope this helps somebody. Jon

Unplug the machine. Remove the 4 screws on the back panel of the washer. Loosen the tub pulley bolt. Remove the old belt (mine did not completely break, it was shredded and slipped off the pulley). Replace with the new belt. Tighten the pulley bolt. Put the back panel on. Plug in the washer. It is working like new. :)