GBXR2080T3AB General Electric Washer - Instructions

I pulled the front panel off as described in the video on Partselect.coms video (very helpfull) and unpluged the pump, I was able to test the original pump and determine it to be good and ultimatly that was not the problem. However had it been it would have been a simple fix. returning the unused part was super simple and painfree!

First I uplugged the machine and removed the front cover of the machine by prying outward at the top corners with a screwdriver. Then I removed the two bolts from the mounting bracket and unplugged the electrical wires. Then using a pliers I squeazed the hosed clamps and slid them back on the hoses and pulled the hoses off the pump.

To install the new pump, simply reverse the order and check for leaks. The whole process took about 20 minutes.

I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!

It was as simple as removing the front cover of the washer. After unpluging, using pliers, remove the two hoses on the pump and disconect the two power plug ins. Two bolts that mounted the pump to the frame of the washer were removed and the pump comes out. Re-install the same way with the new pump from partselect and it worked great.

just like the video showed/////only idid not kno the water would escape from one of the hoses when removed///video did not prepare me for this

My washer was full of water after it wouldn't drain as part of the wash cycle. I used a Wet/Dry vacuum to remove the water from the tub. Followed the video provided on this part page. When I pulled the hose from the wash tub to the pump at least a gallon of water that I was in the bottom of the tub and hose rushed into the base of the washer. It was an unexpected mess to clean up a the end of the job. Pump was fairly easy to remove from the washer, but reinstalling the hoses to the pump was slightly more challenging. The hose from the tub to the pump is about an inch too short to make this an easy fit. I had to have my wife hold the hose clamp open with the channel locks while I positioned pump onto the hose. After the hose was installed, the second hose was much easier to install. With the new pump the washer running like a champ!

i took out the two screws that mount the pump to the base of the washer, then i took a pair of channel locks to disconnect the clamps on the drain lines. thats it. i put the new one in and it works great!

took off the front and replaced easily. I tested it and it worked! The trick to remove front panel is use 2 screwdrivers, one on side, one in front even to lid edge.

Replace

I figured out the problem,watched the video instructor and i did it,couln'd be easier guy h

ordered new one put on works like a new machine your repair website really helped.

the repair was easy. I will be call you again, thank you.

Trouble shooting on internet only mentioned worn drive belt as a cause for no spin. No mention of the possibility of a transmission problem burning out the centrifugal clutch. So the drive belt was ordered and when I checked tracking when it was late, I was informed that it was already delivered and signed for by some stranger, jmorris. Later that night I found the package at my door to late to do the repair that night. The next evening the repair was attempted and it was not difficult with the youtube video for guidance. Back together but it did not spin or agitate. On the third run dthrough the procedure I noticed that the clutch was really hot and the notor was not locked. But the big pully would not complete but bart of a revolution and hard stop. The repair was a failure and after the time spent diagnosing the wrong problem with inadiquate trouble shooting on the internet chart and the time ordering and waiting for the second chance delivery. The failed repair delayed to the point that the customer did not have time to do their laundry berore their weekend trip. They will have to get a new machine after waisting so mych time with a less than fully informed repair attempt. The internet trouble shooting help was inadequate. The delivery of the parts was botched using FedEx instead of UPS. At the last minute after hours of involvement it came to light that the machine was history and we were suckered into buying the wrong part and running out of time for the customer to ready their clothes for their trip. I felt so bad of the machine resisting the repair process thaqt I discounted my labor time and told the customer pay me what they felt would be ritght. It was not all part selectt's fault but they had their page in the story.

remove screws from bottom of washer to remove the bottom of the washer so you can access the pump and motor assy. and remove two hose clamps.

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !