GCXR2100T2WW General Electric Washer - Instructions

Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.

Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.

The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It required a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.

My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off and putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!

Had never repaired a washer before, but have several tools and enjoy working with my hands. Knew it would be cost prohibitive to call a repairman, and didn't have anything to lose. Quick delivery from partselect -- reasonable price, too. This was as easy as simply taking the whole washer apart (NOTE -- there are instructions behind the knobs inside the unit that are very helpful!) replacing the transmission and putting it all back together. Hardest part was getting the hub nut off of the transmission axle. To get it off (REVERSE THREADED, so 'tighten' to 'loosen') I used a 1 11/16 socket and impact wrench. Use the same tool to tighten (but go EASY...don't overtighten). This was not difficult, but just took some time. A couple of evenings later, we were washing again like NEW. Part cost around $160, labor was 'free' and much less than a new $500 top loader or $800 front loader. If you enjoy taking things apart and have some tools, then go for it!

First I unplugged the washer from the wall and then I removed the front panel with a putty knife. I slid the putty knife in between the front panel and top of the washer to disengage the two clips (see parts diagram on Partselect.com). Then I removed the four nuts holding the motor. I then removed the motor and old belt. I installed the new motor and new belt and tightened the four nuts ensuring proper belt tension. The new motor included a new wiring harness and capacitor. The wiring harness installation instructions were easy to follow. Besure to read the all the instructions first before beginning to cut the old harness. Once the wiring harness was installed, the machined worked just like new. I did not need the Retaining Clip for Clutch since the new motor and clutch kit come as one assembly and there is no longer an actual clutch. The two-speed motor just has a pulley for the belt.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

Removed washer to garage (after water was pumped out by the washing machines pump). Tipped it over to access bottom of machine and removed about 8-10 nut machine screws. Slipped new clutch on and used old retaining clip (new one was too difficult to get on). Loosened motor mounts on the drive motor and slipped on belt. Positioned the motor to put a good amount of tension on the belt and tightened motor mounts in a star pattern. Works great, even with heavy loads (like jeans). Easy easy.

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and the tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

I loosened the 4 screws that hold the motor and clutch in place. Removed the motor and clutch and turned upside down. Removed the retaining clip. Pulled the old clutch off (does not come off very easy). Stuck the new clutch on and replaced the retaining clip. Slapped it back into the machine.

I loosened the four nuts holding the motor in place, slid the motor toward the tub to slacken the belt enoug to remove it, then replaced old belt with new belt, pulled motor back in place until belt was tight, then tightened the four nuts holding th emotor in place.

I followed the instructions provided by GE that were stored in the control section of the washer. Removing the hub nut was a huge pain. It took Liquid wrench, hammer, pipe wrench and patience to remove it. Other than that it was fairly easy. I didn't like the way the tub seal fit so I used some silicon gasket making material to help make sure the seal sealed good against the tub.

Finding the disassembly instructions in the control panel was very useful. After disassembly and inspection obviously the transmission had lost oil and deteriorate the belt and actually threw it off. Finding your web site was very helpful. The exploded views parts catalog were great! We had it rush shipped. It was great to speak with a representative on a sunday was excellent. The rep was knowledgeable and we concurred on which part were needed. Tracking number was correct via e-mail but only rec'd tracking number for one of the two packages which was stressful at the fedex office at pick-up. All items were rec'd on time assembly was straight forward. The basin retainer nut came loose after 5 loads and made a terrible noise. I applied blue loctite to nut and reinstalled. Seems to be working correctly. Bought an extended warranty which added 4 yrs. Washer failed 2 months after warr. Expired. Figures!! Great experience with partselect thank you.

1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.