GBSR1080A0WW General Electric Washer - Instructions

Fold back control panel, pull water level knob off, and unlatch pressure switch. reverse procedure to install new switch.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

unscrewed the old coupling, brushed off yucky build up and replaced, ta da back to washing clothes constantly !

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

The hardest part of this repair was actually getting the panel off to get at the timer itself. You need a special type of screwdriver with a torc head, (not sure about spelling) ( looks like a phillips head but has an extra "prong") . After that it was as easy as unplugging the old one and plugging in the new one. piece of cake.

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Repair went good, only wish i had bought a new tub seal, washer, an split ring....but i managed to save the original ones an it seems to be working like new again! thanks Partselect!!!!

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

I used a socket set to remove broiler element. It was stiff after so many years, but no problem. All was going well until I pulled too hard on the old element(I'd recommend jiggling if stuck, not yanking) & 1 of the 2 connectors pulled loose & fell behind the back. After my initial panic, I summoned my courage, unscrewed the coverings in the upper back of the stove, found the lost connection, pushed the new element ends through the holes from inside the oven (easiest way to hook it up at this point), plugged it in from the back, pushed it back thru into place inside the oven, reattached everything (front & back), & it worked PERFECTLY! Had I not made a mess of it, it would have taken approx. 5-10 minutes. As it was, it took approx. 15 minutes. EASY!

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased

remove two screws slide out. slide new one in. put two screws back. done.

Removed the bolt holding the agitator coupler on, replaced it and the bolt then slid the agitator on the coupler and the fabric softener dispenser on top of that.... so easy!!