GBSR1080A0WW General Electric Washer - Instructions

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.

I turned off the breaker to the range. I removed 5 screws holding the control knob carriage. I loosened the 2 screws that hold the control knob to the carriage. I removed each wire 1 at a time from the old control knob and hooked them up to the new one. I replaced all the screws and turned on the breaker.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

I first removed the screws from the top of the washer electric panel. Then pulled it forward. I then removed the plastic clip from behind the knob. Then I removed the screw holding the timer in place. And then removed the one single wire and the connecting plug. I then plug both wire assemblies in to the new one, slid both ears under the brackets and inserted the one screw. Then just put the screws back in the top. It works great!!!!!

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.