C978-97222210 General Electric Washer - Instructions

Unplugged power to dryer. Opened door and removed the two screws that hold the top panel on. Removed top panel and set aside. Then removed the two screws that hold the front panel secure and leaned front panel towards me. Replaced parts with absolutely no tools. Reverse steps to assemble dryer. The videos are very informative and give you the confidence you need to do it yourself.

Ensure washer drum is empty of water before attempting repair. Disconnect the power to the appliance. Remove the front washer panel (a metal putty knife if needed to unlock the two upper tabs which releases the panel). Locate the existing drain pump at the bottom of the unit. Disconnect the two wires from the drain pump motor (one orange, one black/white). A pair of pliers and a gentle pull should do it. Using a small ratchet and socket, loosen and remove the two bolts that secure the drain pump to the bottom panel of the washer. Using a pair of pliers, squeeze the factory hose clamp on the large drain tube that connects the pump to the drum and remove the hose from the pump, being careful to capture any residual water from the drum. A towel is helpful to absorb the water. Repeat for the smaller discharge drain tube located on the side of the pump. Once both tubes are disconnected, remove the old pump. Install the new pump and reconnect everything in reverse order. Connect the small drain tube to the side of the pump. Connect the large drain tube from the drum. Ensure the clamps are properly secured. Insert and hand-tighten the two bolts that secure the pump to the bottom panel of the washer, making sure the bolts are snug but being careful not to overtighten. Reconnect the two wires to the motor. Restore power to the appliance. Run a quick wash cycle to ensure pump is working correctly and check for any water leaks. When satisfied, reinstall and secure the front washer panel.

Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

2 Screws hold top on, removed top, 2 more screws hold front panel with door on, removed front panel. Unclipped front drum bearing installed new one with new sliders put back together.

Dryer was making a horrible noise. When I took it apart I noticed that the from side dryer bearing was ruined. Ordered the part with the slide bars and replaced...Works great...

Looked at the diagram on your web site and replaced part

I followed the step by step instructions provided by Video! Very informative, easy to understand and follow! If I can do it myself, anyone can! Thank you !

I read the repairs that others had posted and how they did it. It was really easy. My only complaint is that I didn't know that I needed the slides that attached to the bearing and couldn't find them on the repair list. My dryer had a spot for 4 of them and only 1 was left. Otherwise, being a female, I felt great to be able to fix it myself! Thanks!
Let me also say, I only have one good working arm/hand.

Remove top (2 screws) and front (2 screws), snap out old drum bearing, put new slides in new drum bearing and install in dryer. Reinstall front and top of dryer.

Replace both micro switches.

My advise is to watch the video prior to starting, while fresh in your mind start the repair, it's so simple, I actually thought I was the Maytag Repair man,

Open the door and removed the part. Installed the new part and started the dryer.

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.