52150119 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melissa from Karns City, PA
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer would not fill.
removed 3 screws from the back. Then removed the little water line clamp. unplugged the 4 wires. took the new part. plugged it in. put on the water line clamp. put the 3 screws back on. put the hoses on the back again. turned on the water supply. and started washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dana Point, CA
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no hot water
Pulled top off and removed corner mounting plate then unscrewed mixing valve.replace wiring to valve and mount new valve in it's place .put back support and corn brace .then attached hoses and put back in service .work great for 20 plus yr machine.thanks tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leigh J. from Aurora, IL
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water leak
I took the back cover off of the washer, studied my next move and jumped in.Easy Lou-eezee!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney J from Derby, KS
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No hot water entering machine.
Did some checking to make sure the filter, screen and hose were unobstructed. Turned off water at faucets, disconnected hoses and drainage hose. Unplugged machine and pulled out far enough to access back. Used nutdriver to remove 6-7 screws that held the back on, and then inlet valve plate. Removed clamp on outlet hose, then one by one removed wires, making sure to connect them to the same connections on new valve. Re-connected outlet hose and reversed procedure. Easy fix. Went ahead and replaced hoses while I had it out.
Was this instruction helpful to you?
Thank you for voting!
Water leaking out the bottom of washer during fill
Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Delray Beach, FL
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hot water would not pour out at normal rate.
This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from millen, GA
- Parts Used:
- WH1X2757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
teeth worn off of knob
removed old knob pushed on new nrw one locked on wifh key
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Summerville, SC
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No water going into the washer at rinse cycle
Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Dekalb, IL
- Parts Used:
- WH1X1944
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Agitator wasn't turning
Very straight forward install. First removed the agitator itself by pulling straight up on it. Then removed the agitator coupling without the need of any tools just pull it straight off. Install new coupler and agitator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Ormond Beach, FL
- Parts Used:
- WH1X2757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob no longer worked
An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from mooresville, NC
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
slow cold water
quck delivery thanks. removed back panel and valve assembly. replace unit,and replaced panel. yep it works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from New Bern, NC
- Parts Used:
- WH1X2757
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Selector knob would not engage to select wash cycle. Teeth on knob were worn/broken.
Removed existing knob by using pliers to release clip from shaft. Inserted new knob (with clip attached) onto shaft and aligned with shaft groove to engage clip. Easy breezy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from REDWOOD, NY
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I closed my vacation cottage for the winter and neglected to put a small amount of RV antifreeze in the washer hoses and the plastic valve developed a hairline crack which sprayed water out when hooked up again in the spring.
Since the valve sprayed water out in one particular spot, it was easy to determine what part I needed. After I received the part from "Part Select" it was super easy to replace and took about 10 min. and the washer was good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Kansas City, MO
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washing machine would not fill
Unplugged washing machine from electrical outlet. Turned off water supply to washing machine. Removed inlet hoses. Removed 2 screws to get panel off that water valve attaches to. Removed the panel for access to water valve. Removed fill hose from water valve and then unbolted valve from panel. Made diagram of electrical wiring to ensure correct placement on new valve. Attached new water valve, electrical wires and fill hose to valve. Installed panel in machine and hooked up inlet hoses. Turned on water supply and inspected for leaks. Turned on washing machine to verify filling and repair was OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Mexico, MO
- Parts Used:
- WH1X2117
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
wouldnt turn to wash cycle was turning manulie
its great and saved me lots of money enjoy my washer again
Was this instruction helpful to you?
Thank you for voting!