52750-4 General Electric Washer - Instructions

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

popped lid pulled front scraped old seal off ,good kit ,worked great. you guys are great 2nd day delivery,on parts for fridge ice maker solenoids and dryer parts. you got me for a customer from now on. thank you. steve

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

Real simple, Unplug power cord from the wall outlet. Then open the top of the dryer by inserting a flat blade screwdriver under the front and pry up till the top snaps open. Lean the top to the back to keep it out of the way. Remove the 2 screws that held the front on and remove the wires for the door switch and the light. Remove the front by letting it lean out about 8 inches and lift it up out of the two bottom clips. Then just lay it any where it will be easy to work on. Clean where the new guide will go. Then just follow the instructions that came with the part. After the adhesive is fully dry just reverse the process and you are done.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

no problem open top remove front install new belt

tilt up lid, remove front panel, replace guide, clean out dryer and reinstall.

Unhooked old hose and replaced with new one.

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

First of all to all you females out there, I am one and this is easy. It was a stacked washer/dryer and the dryer is gas. I unplugged the power, didn't unhook the gas and left them stacked, not a problem. Next I pushed in the 2 clips at the top with a small screwdriver while at the same time prying up on the top with my chisel, popped the top up and unplugged the wire bundle that's attached to the front panel. A few inches down on the inside of the front panel are 2 screws, I removed those. Then I pried the front panel off - there are 4 clips 2 on each side holding the front panel on. I pulled off the felt strips leaving a bunch of "hair". I read the other repair stories saying they'd wished that they'd used stronger solvent to remove the old glue and "hair" so I used laquer thinner and it worked great. Just saturate your rag and get the old felt and glue really wet and then come back with the chisel and the felt and most of the glue comes off and not the paint. I just kept going back over it with the saturated rag and chisel and it was pretty easy. I then put the glue on the felt strips, attached them, and used a ring of bungee cords to make a clamp around them 'til they dried. Put dryer back together and it works great. Also when you've got it apart - it's a good time to vacuum out the inside of the dryer.

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.