52750-5 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rownak from Austin, TX
- Parts Used:
- 131859104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Several knob broke. Could not select and turn on washer-dryer combo
I removed the broken knobs and after that it was just plug and play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlson from Chicago, IL
- Parts Used:
- WH23X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer would not pump out the water and odd noise
removed front lower panel to access pump assy,removed the pump hold down scews and then moved the two hose clamps back then took out assy,just reverse the process to install,always disconnect power and turn off water supply to unit before any service is done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from port jefferson station, NY
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
crack in drain hose
First I went on-line and found a download for the parts catalogue which contains a schematic for the washer. After looking this over I could determine how to get the washer apart! After getting the front panel off, I disconnected the drain hose from the pump with a pair of water-pump pliers. As I pulled this hose out, water spilled out all over the floor, so I then cleaned that up. Next I connected the new hose and put the machine back together. This job would have cost me over $150 if I had called in a repairman. PartSelect saved me so much money, and I thank them so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Martinsville, IN
- Parts Used:
- 5303207102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken Door Strike
After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.
I also noted that the new part was of a better design than the original. It should not need further attention.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hyattsville, MD
- Parts Used:
- 131461200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Discharge hose was leaking
This is a newer washer, but I don't know the age. I just bought the house...!
I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.
I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Arlington Heights, IL
- Parts Used:
- 5308001614
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
knowing how to open the top
I unpluged the machine. Pried out the old switch with the tip of a screw driver. Pried off the connectors, there was not enough extra wire for me to connect the new switch through the front of the machine. I pushed the new switch in place. Using the screw driver I carefully pried open the top front of the machine { there were 2 plastic spring clips securing the top}. I placed a wash bucket on the drum to hold the top open , connected the 2 connectors to the switch and snapped top back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rene from las cruces, NM
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cloths being torn in dryer
first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Horseheads, NY
- Parts Used:
- 131398303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Tub cover seal leaks water.
Lifted lid/top of washer pulling straight up and removed front panel (2 screws at bottom). Removed old tub cover by prying tabs off the tub clips. Aligned new cover and seal over tub and pressed down to engage tabs with tub clips. Easy repair. Re-installed front panel and 2 screws, closed washer top by pressing down to engage the spring clips. I used anti-seize grease on the front panel screws and I used a small amount of petroleum jelly on the top/lid spring clips to make future removal easier(just in case.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Orlando, FL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Nasty, rusted lint trap didn't function any longer
The part arrived in just a couple of days and was exactly the right one. Simply removed the old and replaced and now the dryer works 100 percent better. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Palm Desert, CA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Brown stains on clothes.
Followed your website repair guides and the great belt replacement video.
Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.
Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.
John H.
Palm Desert, CA
Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.
Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.
John H.
Palm Desert, CA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ruoli from Germantown, MD
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer's drum doesn't run
Follow YouTube "how to change dryer's belt" some video is very clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LAWRENCEVILLE, GA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
The video on the site is easy to understand and a snap to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Van from BLUFFDALE, UT
- Parts Used:
- 131475320
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
My heating element had gone out
Don’t do like I did and undo the drummer from the back of that thing pulled off the bearing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BIRMINGHAM, AL
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace Drain Hose
Ordered this part to replace a drain hose that had been cut short on the washer. Installation was straight-forward. Removed the two front screws to access the cabinet. Locate the drain hose and remove with a pair of pliers. Install the new part and attach the clamp with the pliers just like removal. Took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!