GWSE5190E6WW General Electric Washer - Instructions

You tube is the only way to go!

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Pretty much the entire machine has to come apart to replace a transmission. The thing to know that no one mentioned is that the hub nut is reverse threaded - that means righty loosey.
Even if I had known, I tried it both ways and I doubt I could have gotten it off without the chisel as the others also had to do. Split ring was also frozen in place by hard water and soap scum so had to break that cheesey piece of aluminum off also. If you are taking apart your washer, I advise ordering these 2 parts so you will have them after you destroy the old ones trying to get to the part you need to fix.

Thanks to parts select for the exploded diagram!

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

Problem was intermittent. It would happen once a month or so. Eventually I set next to the machine and kept turning it On and OFF through cycles for about a half an hour until it failed and I was able to confirm that problem was with the water valve.

Buying and replacing the water valve was easy.

WARNING: UNPLUG THE WASHING MACHINE FROM THE WALL BEFORE ATEMPTING ANY ELECTRICAL WORK ON YOUR WASHING MACHINE!

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

My son repaired the washer . It was really easy to fix. He had it working in about 15 minutes. Thanks to PartSelect's fast delivery service I was only without my washer 2 days.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

Easy enough. I had some help tightening the hoses to the inlet valve. I watched the video about how to repair and it was straight forward and easy to follow. You'll need a bit of strength to tighten the hoses to the dual water inlet valve. Be precise when lining up the threads of the hose and the inlet valve...don't force it...find it...if it goes on crooked it will strip the threads and wreck it. Recommend purchasing some plumbers tape to wrap on the the threads of the Dual Water Inlet Valve. Fixed the dripping water problem immediately.

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.