GCVH6600H0BB General Electric Washer - Instructions

Took it apart per the video and reinstalled

The repair video was almost perfect. I would not have even attempted the repair without the video as I am not a handyman at all. The diagnostic feature based on the symptoms was invaluable. I originally took the front of the washer off because I thought the rubber seal around the door was leaking.It was like 67% of the problem. But after checking the front seal carefully, I determined it wasn't. The next most likely issue as only rated 19% but when the water inlet pipe, I was actually tickled to see a crack in the plastic pipe. I ordered on line on Monday and with the cheapest shipping, I received my part in the mail on Thursday. I would highly recommend using Part Select for diagnostic, parts and repair. I will definitely use again. If I could make one recommendation to Part Select, it would be to do a close up during the video when the technician is working with a part, i.e., the wiring that goes around the rubber seal.

I won't bother repeating other people's comments. My repair took a bit over 2 hours. I watched 2 different videos and thought the repair was doable. To remove the first wire band holding the boot seal to the front panel I found using an awl to grab the eyelet near the spring was easier than using a needle nose recommended in the video. To remove the second wire band I used an offset screwdriver. One video I watched recommended removing the lower counterweight to get at the band's screw - I did not do that. Putting the new boot seal into the first groove and installing the wire band was the most time consuming part of the job. I did not have extra hands to help. I recommend the second pair of hands for that part to save time. The rest of the install was easy.

followed partselect video instructions. Easy but takes time. Thank you

Watch the video posted on PartSelect. It was excellent and walked step by step through the whole repair.

I only ran into one issue not included in the video. In order to remove the inner ring holding the boot seal, I had to remove the weight at the bottom of the tub. This is easy to remove with a wrench, but took two people to reinstall. You only need the second person for 1-2 minutes to hold the weight while you align the bolts.

The most difficult part is ensuring you replace the hex nuts and screws in the same location. I took pictures as i removed them to know where to reinstall.

Total repair time was probably 1.5 hours.

Before disassembling anything be really sure that the little things are reassembled just as they were prior to removal.....

My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! Hook up the drain hose with pliers and screw the motor to the frame and that's it!

You probably won't want to publish this but it worked. The baffle on the GE washer I have required a complete tear down of the machine's front and outer waterproof drum to get a tiny little screw out. Very poor design if you ask me. And, I was not about to pay a technician for a massive overhaul to get a 3/8" long stainless screw off the broken remains of the baffle. So, I measured how far over the screw was from the pipe that feeds detergent, softener and bleach into the drum. I drilled a 3/8" hole in the outer drum. After removing the screw and installing the new baffle (which took all of about 2 minutes), I put a 3/8" hole plug I bought at Lowes into the hole with two part plastic epoxy. Then I covered the entire hole plug with a crown of epoxy. Five minutes later when the epoxy set, I ran a load of clothes. It ran perfectly and did not leak. I know. I know. This is not what you would recommend to your readers but it worked. I was brought up fixing everything around the home and any effectie shortcut was/is used. Oh,by the way, if you know which GE engineer thought up the design for this baffle installation, whack him on the head once.

Unplug the machine. Remove the 4 screws on the back panel of the washer. Loosen the tub pulley bolt. Remove the old belt (mine did not completely break, it was shredded and slipped off the pulley). Replace with the new belt. Tighten the pulley bolt. Put the back panel on. Plug in the washer. It is working like new. :)

VERY simple, just took two philips screws off of the door, replaced the broken part, put the screws back in! LOL

All i did is pull the front panel off,then n removed the front clap with channel locks then the side clamp the same way.i then removed the main clamp with a Phillips screwdriver very simple not ever 15 minutes to do

Step 1- pull washer away from wall. Step2- unplug power, shut off water and disconnect lines, and disconnect drain line. Step 3- unscrew 3 screws from bk and 3 screws from behind control panel. Step 4- remove back of control panel and top of washer. Step 5- unplug wires from old valve and plug into new valve to avoid wrong connection take out screw from back releasing old valve , insert new valve and put back screw. Step 6 put top of washer and back of control panel on and insert screws. Step 7- reconnect hoses and drain , plug washer in and test. All done. I recommend adjusting to level if necessary at this point before pushing back against wall. Good luck. Hope this helps somebody. Jon

hold drive pulley from turning and used socket wrench to remove nut. then pulled off pulley from shaft and belt came off same time. very carefully filed the flat sides of the shaft end where the pulley slides onto. careful not to overfile or round out the she shaft end. carefully tap in place the pulley onto the shaft. install a new nut and tighten it approx. 40 ft pounds or 1/4 turn past tight. do not reuse old nut. pulley comes with a new one and the nylon on the old one is no good once used. once pulley is tight install the belt first onto the motor shaft then work the other end of the belt onto the pulley from top end then turn the pulley wheel counter clockwise as you push more belt onto the pulley wheel. kind of like putting on your bicycle tire on your rim.

I followed the instruction on your site. I disconnected the power to the washer turned off the water turned on the nearest faucets to drain the lines. I removed the water hoses from the machine then took the three screws out of the back at the top of machine that held the lid on then removed the three screws on the top of the lid that hold the plastic piece to the front panel and pushed the lid toward the back and it lifted off. I then took the metal ring clamp off the water line attached to the water inlet valve and took the screw out that is on the back of the machine holding it on removed the wire plugs one at a time and put them one at a time on the new inlet valve so I would not get them mixed up. I then put the valve in place reconnected the water hose and metal clamp put the screw in the back to reattach valve the machine put the lid back on in reverse to removal reattached water hoses to the inlet valve turned the water back on plug in the power and immediately used the machine which works like new 20 minute job from beginning to end. By the way ladies if I can do it you can do it. TC

1) Remove door hinge cover. 2) Remove hinge door plate. 3) Remove hinge door pin using a hammer and striking tool if necessary. 4) Using needle nose pliers, remove gasket inside clamp from the door boot seal. There is a spring at the bottom that should allow you to pry this part out and off. 5) Pull the door boot seal away from the exterior cabinet to allow access to the hinge. 6) Remove the hinge screws 7) You should now be able to remove the hinge. 8) Install new hinge and reverse steps to reassemble.