57441D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ray from Ventura, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washer did not drain completely with water on floor, drain pump frozen.
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Wickliffe, KY
- Parts Used:
- WH43X10034, WH43X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator kept coming off
Removed the bolt holding the agitator coupler on, replaced it and the bolt then slid the agitator on the coupler and the fabric softener dispenser on top of that.... so easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Peabody, MA
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking hose
Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rochester Hills, MI
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Wash basin wobbled excessively
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Santa Clarita, CA
- Parts Used:
- WH49X10042, WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Agitator stripped and came off coupling
First I took off the old coupling (one screw). Put the new coupling on, lined up and snapped the new agitator onto the new coupling.
Repair took les than 5 minutes. The longest part of the whole process was lining up the agitator to the coupling.
Repair took les than 5 minutes. The longest part of the whole process was lining up the agitator to the coupling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jayme from drummonds, TN
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
My washer would not drain the water out.
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Shannon, GA
- Parts Used:
- WH02X10383, WH02X10265, WH2X1199
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water leaking in the floor occasionally with no obvious leaks anywhere
ORDER Spanner wrench for GE tub nut. Impossible to remove hub nut on a washer with age without it. Purchase 1 11/16 in spanner wrench, tub seal, hub nut , split nut
and washer under
agitator all at one time or you will struggle with this repair. The few cents you save is not worth it, the video they provide does a good job but theirs washer
is new hope this helps
and washer under
agitator all at one time or you will struggle with this repair. The few cents you save is not worth it, the video they provide does a good job but theirs washer
is new hope this helps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett F from Sag Harbor, NY
- Parts Used:
- WH13X10025, WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
A Leak Thought It Was A Hose At First But Still Leaked When Washer Was Not Running
Removed all visible screws to expose water valve . . Removed water valve , hose & water inlet and replaced with new . Straight forward and simple . Very fast delivery of parts that was huge . . Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- douglas from Stockton, CA
- Parts Used:
- WH16X543
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
tub fell down on one side
after ordering part and getting the wrong part sent to me i was able to finally get right part to my house 2 weeks later, i pulled front cover off with a screwdriver took out broke rod and inserted new part closed cover and hooked power back on and was in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drew from Apopka, FL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Tub straps broken caused excessive wabbling
Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Marco Island, FL
- Parts Used:
- WH13X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Solinoid chattering when cold water was used
Removed 4 screwes on the top of the washer. Layed down the control panel and there was the inlets. Removed two screws and loosened the hose clamp. removed and installed new part.
It did the trick. No more problems.
It did the trick. No more problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Seymour, IN
- Parts Used:
- WH49X10042, WH43X10034
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
defective agitator
the parts you sent were same as G.E. parts and fit with very little labor on my part Just follow the directions parts snap right in place washer is good as new thanks for speedy delivery. L. Neal Seymour In.
thanks for speedy
thanks for speedy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kartik from radnor, PA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Drain hose had a hole in it
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Dublin, TX
- Parts Used:
- WH13X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water continually ran into the washer when shut off and even when it was spinning
removed 4 screws on the top back of machine, undid 2 screws and the hoses, pulled old part out, put new part in. Walla!!!!washer is fixed!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from Merced, CA
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
drain hose cracked, leaking water, when in use
It was easy, I just removed the old drain hose clip with a screwdriver. Next, removed the old, cracked hose, inserted the new one, and screwed the new clip in.
The best part about this story is the incredible service I was given, by this company. I bought the machine at Sears, so I assumed I could find the hose their. No, they instructed me to go to Orchard Supply(their sister store), I purchased a drain hose, the clerk told me to buy, but the water was still leaking. So, I went on-line and found the right hose, and now I will continue to purchase what I ned for my machine from your company. REALLY Fast Service. Thanks
The best part about this story is the incredible service I was given, by this company. I bought the machine at Sears, so I assumed I could find the hose their. No, they instructed me to go to Orchard Supply(their sister store), I purchased a drain hose, the clerk told me to buy, but the water was still leaking. So, I went on-line and found the right hose, and now I will continue to purchase what I ned for my machine from your company. REALLY Fast Service. Thanks
Was this instruction helpful to you?
Thank you for voting!